All Products

SKU: DF-DFR0577

The Gravity I/O Expansion Shield for Pyboard connects your Pyboard v1.1 to the DFRobot Gravity sensor and module ecosystem with colour-coded plug-and-play connectors. No soldering is required — simply plug Gravity-compatible sensors and modules into the clearly labelled ports. An onboard externa...

SKU: DF-DFR0518

Micro:Mate is a tiny micro:bit I/O expansion board for learning electronics and building DIY projects.Micro:Mate expands 6 sets of 3-pin I/O interfaces, capable of connecting DFRobot Gravity series modules, servo motors, sensors and jumper wires. Additionally, Pin 8, 12, 16 support voltage switch...

SKU: DF-SEN0322

The Gravity: I2C Oxygen Sensor is based on electrochemical principles and it can measure the ambient O2 concentration accurately and conveniently. With high anti-interference ability, high stablility and high sensitivity, this arduino-compatible oxygen sensor can be widely applied to fields like ...

SKU: DF-SEN0411

The Gravity: LIS331HH is a high-performance 3-axis linear accelerometer with ultra-low power consumption of just 10 µA in low-power mode. It offers user-selectable measurement ranges of ±6g, ±12g, or ±24g and delivers 16-bit data output with configurable data rates from 0.5 Hz to 1 kHz. Using th...

SKU: DF-SEN0409

The LIS2DW12 is an ultra-low-power high-performance three-axis linear accelerometer. It has user-selectable full scales of ±2g/±4g/±8g/±16g and is capable of measuring accelerations with output data rates from 1.6 Hz to 1600 Hz. The sensor comes with two independent programmable interrupts and a ...

SKU: DF-FIT0896

Note: One package has 10 cables.This high-quality 30cm digital sensor cable is equipped with 3 pin PH2.0 plug connector on one side and Dupont male connector on the other side. One package has 10 cables. Compatible with breadboard and DuPont wire spacing, these cables use materials that are ...

SKU: DF-SEN0551

This Gravity: liquid flow sensor is designed based on the electromagnetic principle. It adopts O-ring rubber seal and uses silicone sealant at the outlet end to strength water-resistance. With high anti-interference and anti-impact, the sensor offers reliable performance and long service life. Al...

SKU: DF-SEN0550

This Gravity: Liquid Flow Sensor is designed based on the electromagnetic principle. It adopts O-ring rubber seal and uses silicone sealant at the outlet end to ensure good waterproofness. Also, it embraces high anti-electromagnetic interference and anti-vibration capabilities, offering reliable ...

SKU: DF-SEN0223

The Gravity Conductivity Sensor Switch module can be used to detect if an object has electrical conductivity. Its maximum detection value is 10MΩ. It can detect not only coins, wires, metal and other good conductors, but also the human body, fruit, plants and other conductors. By touching the...

SKU: DF-DFR0438

INTRODUCTION The Bright LED module is designed for some special application. It's using a very bright LED component as its light source. Compatible with DFRobot gravity 3-Pin interface, plug and play. What you need is just a digital signal, you can drive it directly. Besides, the LED is so b...

SKU: DF-DFR0627

The Gravity IIC to Dual UART Module converts a single I2C connection into two independent hardware serial ports. Each sub-UART has its own 256-byte FIFO buffer for transmitting and receiving, with individually configurable baud rate, word length, and parity settings. Most controller boards like ...

SKU: DF-FIT0513

A pack of 10 Gravity-series 4-pin sensor cables, 30 cm long, for connecting I2C or UART sensors to Gravity-compatible boards. Each cable has a PH2.0 4-pin connector on one end and a XH2.54 DuPont connector on the other, compatible with standard 2.54 mm breadboard pin pitch for easy prototyping. ...

SKU: DF-DFR0067

This Gravity-compatible DHT11 sensor provides calibrated digital temperature and humidity readings via a single data pin. With an integrated 8-bit microcontroller and factory-calibrated coefficients stored in OTP memory, it delivers reliable measurements with minimal setup. The Gravity 3-pin int...

SKU: DF-SEN0224

DFRobot presents the ultra low-power Arduino triple axis accelerometer! This device is based around a MEMS LIS2DH chip solution and has high-performance ultra-low power mode. The module is fitted with a Gravity I2C interface for easy plug and play integration in to your projects. The build in...

SKU: DF-DFR0486

The Gravity I²C OLED-2864 is a 0.96″ blue OLED display module driven by the SSD1306 controller. It communicates via I²C and refreshes at up to 60 Hz, making it ideal for real-time data readouts on Arduino and other microcontroller projects. The module uses the Gravity I²C interface for plug-and-...

SKU: DF-DFR0473

Introducing the Gravity Digital Relay Module - the latest addition to DFRobot's Gravity series! This module is a little different to the other relays in our store - not only is it compatible with 5V Arduino boards, but also with Raspberry Pi, BBB (BeagleBoard Black), mbed, Intel Joule, Arduino 10...

SKU: DF-SEN0214

The Gravity Analog 20A Current Sensor measures both AC and DC current using the Hall effect, outputting a proportional analog voltage to your microcontroller. With high-voltage isolation built into the circuit design and a non-conductive acrylic base plate, it's designed for safe use in automatio...

SKU: DF-SEN0209

This is an Arduino compatible piezo film vibration sensor. It is made up of flexible piezo film and converter board. The sensor is able to detect vibration, flexibility, impact and touch. The film is a flexible component comprising a 28 µm thick piezoelectric PVDF polymer film with screen-printe...

SKU: DF-DFR0457

In most Arduino projects, relays are the first choice to drive some large current device. It requires a certain amount of current to drive the internal coil to pick-up contact. But for some MCU, like Intel Edison, Intel joule, lilypad, Raspberry Pi and other microcontroller with limited amoun...

SKU: DF-SEN0220

The Gravity UART Infrared CO2 Sensor uses non-dispersive infrared (NDIR) technology to measure carbon dioxide concentrations from 0 to 50,000 ppm. It offers excellent selectivity with no oxygen dependency, built-in temperature compensation, and a service life of over 5 years. The UART interface m...