All Products

SKU: DF-FIT0882 · MPN: FIT0882

This compact COB LED strip provides smooth purple illumination for decorative lighting, creative electronics builds and small-space accent lighting. It integrates 16 LEDs under a silicone-encapsulated surface, helping protect the LED chips while producing a more continuous output than typical dot...

SKU: DF-DFR0767-4 · MPN: DFR0767-4

Turn a Raspberry Pi Compute Module 4 into a compact dual-Gigabit router, gateway or IoT platform with this mini carrier board kit from DFRobot. The board connects a Gigabit network card over PCIe, giving the CM4 two full-speed Gigabit Ethernet ports with lower CPU usage and improved long-running ...

SKU: DF-DRI0057 · MPN: DRI0057

This compact motion control board is designed to coordinate ST and SC series serial bus servos in robotics projects, with support for up to 253 servos on a single bus network. It combines power distribution, command transmission and telemetry feedback for multi-axis builds such as robotic arms, w...

SKU: DF-DFR1216-1 · MPN: DFR1216-1

This multi-function expansion board adds power, I/O and drive capability to UNIHIKER M10/K10 and micro:bit projects. It is designed for mobile robots, portable interactive builds and maker projects that need more connectivity than the main controller can provide on its own.The board expands your ...

SKU: DF-DFR1195 · MPN: DFR1195

This ESP32-S3 development board is built for long-range IoT prototyping using LoRa, LoRaWAN and Meshtastic. It can be used for one-to-one LoRa links, one-to-many LoRa communication, standard LoRaWAN networks, or Meshtastic mesh networking.The board is designed to be approachable for makers and de...

SKU: DF-FIT0916-MF · MPN: FIT0916-MF

These labelled male-to-female DuPont jumper wires make it easier to keep track of connections in busy electronics builds. Each wire carries I2C/UART pin labelling, helping reduce mix-ups when colour coding or tiny board silkscreen is hard to read.The wire sequence is the same at both ends and fol...

SKU: DF-FIT0916-F · MPN: FIT0916-F

These labelled jumper cables are designed to make Gravity project wiring easier to follow, especially when a build has several similar connections. Each cable carries I2C/UART pin labels so you can identify power, ground, clock/receive and data/transmit lines without relying only on wire colour o...

SKU: DF-SEN0508 · MPN: SEN0508

This flexible capacitive liquid level sensor detects liquid through the wall of a non-conductive container, so it does not need to touch the liquid itself. It is designed for containers with a wall thickness of less than 5 mm, making it handy for sealed tanks, pipes and other setups where a conta...

SKU: DF-DFR1115-915 · MPN: DFR1115-915

This compact wireless node module is designed for long-distance, low-power outdoor IoT projects. Built around the Semtech SX1262 and LoRa modulation, it operates on the 915 MHz US915 band and supports both direct LoRa communication and LoRaWAN networking.It can be used for point-to-point links or...

SKU: DF-DFR0789-R · MPN: DFR0789-R

This illuminated pushbutton module is a simple self-locking switch with a built-in red LED for clear visual feedback. Press it once and the module outputs High while the LED turns on; press it again and the output goes Low while the LED turns off.It is designed for easy use in Arduino, micro:bit ...

SKU: DF-DFR0785-Y · MPN: DFR0785-Y

This LED-illuminated button module is a simple digital switch with a transparent cap and a yellow light. It works like a basic button, but the internal LED turns on while the button is pressed, giving clear visual feedback for interactive projects.When pressed down, the module outputs High and th...

SKU: DF-FIT0897 · MPN: FIT0897

This pack includes ten 30 cm Gravity analogue sensor cables, each with a 3-pin PH2.0 plug on one end and DuPont male connectors on the other.The cables are compatible with breadboard and DuPont wire spacing, making them handy for connecting DFRobot analogue sensors to an IO Expansion Shield or IO...

SKU: DF-DFR1230 · MPN: DFR1230

This Gravity DAC module converts I2C or PWM digital signals into stable analogue voltage or current outputs for control and automation projects. Built around the GP8630N chip, it supports output modes such as ±10V, 0-5V, 0-10V and 4-20mA, with 16-bit resolution available in I2C mode.The symmetric...

SKU: DF-SEN0682 · MPN: SEN0682

This compact full-solid-state LiDAR module uses a 64×8 DTOF matrix to measure 512 points at once, giving robots and automation projects a wider view of what is directly ahead. It is designed for forward obstacle avoidance, local blind spot detection and other short-range 3D perception tasks.Direc...

SKU: DF-SER0057 · MPN: SER0057

This clutch servo is designed for robots, models and other mechanisms where the servo may be pushed, stalled or forced out of position during use. Its clutch function helps protect the servo by allowing it to reset and keep working after the angle is changed by an external force.Electronic protec...

SKU: DF-SEN0455 · MPN: SEN0455

This diffuse reflection infrared photoelectric switch detects opaque objects across an adjustable 0-7m range, making it useful for presence sensing in automation and access control projects.It runs from a 6-36V power supply and provides a switching value output, with a signal indicator for real-t...

SKU: DF-SEN0673 · MPN: SEN0673

The CS30 is an integrated RGB-D 3D vision sensor that combines a Time-of-Flight depth camera with an HD colour imager. It is designed to capture detailed point cloud data for robotics, interactive AI, 3D scanning and SLAM applications.Its depth and colour data can be fused in real time, helping s...

SKU: DF-MBT0044 · MPN: MBT0044

This expansion board turns a micro:bit or UNIHIKER K10 into a cable-free robotics controller for mobile builds. It provides onboard power from a user-replaceable 18650 cell slot and breaks out motor, servo, Gravity IO and I2C connections for adding sensors, displays, AI cameras and actuators.The ...

SKU: DF-MBT0044-1 · MPN: MBT0044-1

This bundle adds motor, servo and sensor expansion to the UNIHIKER M10 single-board computer, using the included Type-C to HY2.0-4P communication cable to bridge the M10 to the expansion board.The board includes an integrated 18650 battery holder so your controller, motors and sensors can run fro...

SKU: DF-DFR0785-W · MPN: DFR0785-W

This Gravity LED button is a simple illuminated push button with a transparent cap, designed for interactive Arduino and micro:bit projects. When the button is pressed, the internal white LED turns on to provide clear visual feedback.The module behaves like a basic digital switch: when pressed do...