All Products

SKU: DF-SEN0411

The Gravity: LIS331HH is a high-performance 3-axis linear accelerometer with ultra-low power consumption of just 10 µA in low-power mode. It offers user-selectable measurement ranges of ±6g, ±12g, or ±24g and delivers 16-bit data output with configurable data rates from 0.5 Hz to 1 kHz. Using th...

SKU: DF-SEN0321

The Gravity IIC Ozone Sensor measures ozone (O₃) concentration from 0 to 10 ppm with 10 ppb resolution using an electrochemical sensing element. Factory-calibrated for accurate readings out of the box, it connects via I2C through DFRobot's Gravity 4-pin interface. Compatible with Arduino, ESP32,...

SKU: DF-DFR0558

This Gravity I2C high-temperature sensor pairs a signal amplification module (MAX31855K) with a stainless steel sheathed K-type thermocouple probe for measuring temperatures up to 800 °C. The module converts the thermocouple's millivolt signal to a 14-bit digital reading over I²C, with cold-junct...

SKU: DF-SEN0678 · MPN: SEN0678

This Gravity air quality module uses Sensirion’s STCC4 gas sensing chip to directly measure carbon dioxide with the thermal conductivity measurement principle. It is designed for compact, cost-effective indoor monitoring nodes where stable CO₂ readings are needed without complex hardware integrat...

SKU: DF-SEN0214

The Gravity Analog 20A Current Sensor measures both AC and DC current using the Hall effect, outputting a proportional analog voltage to your microcontroller. With high-voltage isolation built into the circuit design and a non-conductive acrylic base plate, it's designed for safe use in automatio...

SKU: DF-SEN0228

The Gravity VEML7700 is a high-accuracy digital ambient light sensor that outputs readings directly in lux (lx) over an I²C interface. Built around the Vishay VEML7700 IC, it features a 16-bit ADC, a high-sensitivity photodiode, and a low-noise amplifier — delivering precise light measurements wi...

SKU: DF-DFR0646-R

An 8-digit red LED segment display module with Gravity I2C interface. This module can display numbers, basic characters, and supports 16 levels of brightness adjustment — ideal for clocks, counters, dashboards, and data readouts in Arduino and Raspberry Pi projects. The Gravity connector makes w...

SKU: DF-DRI0056 · MPN: DRI0056

This Gravity haptic driver module is built for Linear Resonant Actuators (LRAs), turning simple I2C commands into crisp tactile feedback for interactive projects. It is powered by the TM6605 driver chip and supports LRA resonant frequencies from 140Hz to 220Hz.The module includes 44 built-in vibr...

SKU: DF-SEN0130

The Gravity MQ5 gas sensor is highly sensitive to LPG, natural gas, and town gas, with lower sensitivity to alcohol, cooking fumes, and cigarette smoke. The analogue output is proportional to gas concentration, and sensitivity can be adjusted via the on-board potentiometer. Gravity interface for ...

SKU: DF-SEN0189

The Gravity Analog Turbidity Sensor measures water clarity by detecting the level of suspended particles. It works by measuring light transmittance and scattering rate, which change with the amount of total suspended solids (TSS) in the water. The sensor provides both analogue (0–4.5V) and digit...

SKU: DF-DFR1036 · MPN: DFR1036

A 1-channel DAC module that converts a PWM signal from any microcontroller into a precise 0–5V or 0–10V analogue voltage output. Built around the GP8101S chip with 8-bit resolution and 0.2% accuracy, it's ideal for driving standard 0–10V or 0–5V controlled devices in automation projects — lights,...

SKU: DF-SEN0239

A digital infrared proximity sensor with adjustable detection range from 0 to 200 cm. Outputs a simple digital signal — HIGH when an obstacle is detected, LOW when clear. The detection threshold is adjustable via a rear-mounted screw, making it easy to tune for different applications. Features t...

SKU: DF-SEN0134

The Gravity MQ-9 gas sensor detects carbon monoxide (CO) and combustible gases including methane and propane. It uses a semiconductor SnO2 sensing element that cycles between high and low temperatures — detecting CO at low temperature (1.5V) and combustible gases at high temperature (5.0V). With...

SKU: DF-SEN0518

The DFRobot Gravity MAX30102 sensor module measures heart rate and blood oxygen saturation (SpO2) using photoplethysmography (PPG). It integrates the Maxim MAX30102 chip with an on-board MCU that processes raw PPG data and outputs heart rate and SpO2 values directly via I2C or UART, reducing proc...

SKU: DF-DFR0785-W · MPN: DFR0785-W

This Gravity LED button is a simple illuminated push button with a transparent cap, designed for interactive Arduino and micro:bit projects. When the button is pressed, the internal white LED turns on to provide clear visual feedback.The module behaves like a basic digital switch: when pressed do...

SKU: DF-DFR0030

A digital capacitive touch sensor from DFRobot's Gravity series. It detects touch through the same capacitive sensing technology used in smartphones — even through thin cloth or paper. The sensor outputs a digital high/low signal, making it a simple drop-in replacement for mechanical buttons in A...

SKU: DF-DFR0554

The Gravity I2C 16×2 LCD features RGB font colours on a black background, allowing you to display text in any of 16 million colour combinations. Using the Gravity I2C interface, only two data lines are needed for both communication and backlight control. The display supports 2 rows of 16 charact...

SKU: DF-DFR0760

The Gravity Speech Synthesis Module converts text to spoken audio in English and Chinese, including mixed-language content. It connects via I2C or UART using the standard Gravity interface and includes a built-in speaker, so no additional audio hardware is needed. The module supports text contro...

SKU: DF-FIT0513

A pack of 10 Gravity-series 4-pin sensor cables, 30 cm long, for connecting I2C or UART sensors to Gravity-compatible boards. Each cable has a PH2.0 4-pin connector on one end and a XH2.54 DuPont connector on the other, compatible with standard 2.54 mm breadboard pin pitch for easy prototyping. ...

SKU: DF-DFR0469

A high-precision I2C real-time clock (RTC) module from DFRobot's Gravity series, based on the SD2405AL chip. It features an internal rechargeable battery that keeps time for 5–8 years without external power, making it ideal for data logging, alarm clocks, and any project that needs reliable timek...