All Products

SKU: DF-SEN0160

A digital weight sensor kit based on the HX711 24-bit ADC, capable of measuring up to 1 kg. The HX711 is designed specifically for weight scale applications, interfacing directly with a bridge sensor to deliver precise, reliable measurements via the Gravity interface. The kit includes both the H...

SKU: DF-DFR0028

This is an arduino tilt sensor. It is used to detect orientation. Inside the sensor, there is a ball that make contact with the pins when the case is upright. Tilt the sensor over and the balls don't touch, thus not making a connection. Here is the principle of tilt sensor to illustrate how i...

SKU: DF-DFR0061

The Gravity Joystick Module V2 provides two-axis analogue control (X and Y) plus a digital push-button switch. Connect the two analogue outputs and one digital output to your Arduino or other microcontroller for intuitive directional input — ideal for robot control, menu navigation, and game proj...

SKU: DF-SEN0161

You may check the latest version - Gravity: Analog pH Sensor/Meter Kit V2 to meet your requirements and Liquid Sensor Selection Guide to get better familiar with our liquid sensor series.Need to measure water quality and other parameters but haven't got any low-cost pH meter? Find it difficult t...

SKU: DF-SEN0159

The Gravity CO2 Gas Sensor uses an MG-811 electrochemical sensing element to detect carbon dioxide concentration in the air. The output voltage decreases as CO2 concentration increases, and an onboard potentiometer lets you set a threshold for a digital on/off signal output. An onboard heating c...

SKU: DF-DFR0265

The DFRobot Gravity IO Expansion Shield V7.1 simplifies Arduino prototyping by breaking out all digital and analogue pins into colour-coded 3-pin (Signal, Voltage, Ground) Gravity connectors. Plug in sensors, actuators, and modules directly — no soldering or breadboard wiring required. Version 7...

SKU: DF-DFR0251

A relay is an electrically operated switch, which has a control system (also known as the input circuit) and the controlled system (also known as the output circuit), usually used in automatic control circuit. It is actually "automatic switch", using a small electric current to control a large...

SKU: DF-SEN0121

This is a steam(water)sensor from DFRobot. This steam sensor can be connected to the Arduino IO Expansion shield directly. The output voltage will increase when the humidity of the sensor surface goes up. Notice:The new version of analog sensor port pin mapping has been changed as the foll...

SKU: DF-SEN0133

This is an Arduino hydrogen gas sensor. It has high sensitivity to Hydrogen (H2) and less sensitivity to alcohol, LPG,cooking fumes . Hydrogen gas is highly flammable and will burn in air at a very wide range of concentrations The sensitivity is able to be adjusted by the potentiome...

SKU: DF-SEN0130

The Gravity MQ5 gas sensor is highly sensitive to LPG, natural gas, and town gas, with lower sensitivity to alcohol, cooking fumes, and cigarette smoke. The analogue output is proportional to gas concentration, and sensitivity can be adjusted via the on-board potentiometer. Gravity interface for ...

SKU: DF-SEN0132

INTRODUCTION This is an Arduino Carbon Monoxide Sensor. It uses MQ7 probe to detect Carbon Monoxide (CO) concentrations in the air from 20 to 2000ppm. The sensitivity can be adjusted by the potentiometer. The output is proportional to the density o...

SKU: DF-SEN0129

INTRODUCTION This is an Arduino CH4 gas sensor. It uses MQ4 probe which is able to detect nature gas, CH4. It is less sensitivity in detecting alcohol, cooking fumes, and cigarette smoke. The sensitivity can be adjusted by the potentiometer. The output is ...

SKU: DF-SEN0131

INTRODUCTION This is an Arduino Propane Gas Sensor. It uses MQ6 probe to detect iso-butane, propane and liquefied petroleum gas (LPG). It is less sensitive with alcohol, cooking fumes and cigarette smoke. It can be used in gas leakage detecting equipment in...

SKU: DF-SEN0114

A resistive soil moisture sensor that reads the water content of surrounding soil by measuring electrical resistance between its two probes. Wetter soil conducts more easily (lower resistance), while dry soil conducts poorly (higher resistance) — giving you an analogue voltage output proportional...

SKU: DF-SEN0237-A

This is a dissolved oxygen sensor kit, which is compatible with Arduino microcontrollers. This product is used to measure the dissolved oxygen in water, to reflect the water quality. It is widely applied in many water quality applications, such as aquaculture, environment monitoring, natural s...

SKU: DF-FIT0511

The Gravity 4Pin Sensor Adapter converts 4-pin sensors to the DFRobot Gravity interface, making it easy to connect compatible sensors to Gravity-enabled controllers. Features a press-type terminal for quick, tool-free wire connections. A 3.3V/5V power switch provides flexibility for different se...

SKU: DF-DFR0504

The Analog Signal Isolator can isolate analog signal and provide isolated power to sensors. It can effectively prevent sensor signal interference and apply to multi-parameter water quality monitoring sensors. Because usually sensors will be interfered by the other sensors during the measurement,...

SKU: DF-SEN0228

The Gravity VEML7700 is a high-accuracy digital ambient light sensor that outputs readings directly in lux (lx) over an I²C interface. Built around the Vishay VEML7700 IC, it features a 16-bit ADC, a high-sensitivity photodiode, and a low-noise amplifier — delivering precise light measurements wi...

SKU: DF-SEN0244

The Gravity Analog TDS Sensor is an Arduino-compatible kit for measuring Total Dissolved Solids (TDS) in water. TDS indicates how many milligrams of soluble solids are dissolved per litre — the higher the value, the less clean the water. This sensor outputs a 0–2.3V analog signal that can be read...