All Products

SKU: DF-SEN0321

The Gravity IIC Ozone Sensor measures ozone (O₃) concentration from 0 to 10 ppm with 10 ppb resolution using an electrochemical sensing element. Factory-calibrated for accurate readings out of the box, it connects via I2C through DFRobot's Gravity 4-pin interface. Compatible with Arduino, ESP32,...

SKU: DF-SEN0656 · MPN: SEN0656

The CT1780 is a cold-junction compensated amplifier for K-Type thermocouples, designed to make extreme temperature measurement easier to add to microcontroller projects. It digitises the tiny thermocouple signal and provides temperature readings with 0.25℃ resolution over a very wide measurement ...

SKU: DF-SEN0678 · MPN: SEN0678

This Gravity air quality module uses Sensirion’s STCC4 gas sensing chip to directly measure carbon dioxide with the thermal conductivity measurement principle. It is designed for compact, cost-effective indoor monitoring nodes where stable CO₂ readings are needed without complex hardware integrat...

SKU: DF-SEN0228

The Gravity VEML7700 is a high-accuracy digital ambient light sensor that outputs readings directly in lux (lx) over an I²C interface. Built around the Vishay VEML7700 IC, it features a 16-bit ADC, a high-sensitivity photodiode, and a low-noise amplifier — delivering precise light measurements wi...

SKU: DF-DFR0646-R

An 8-digit red LED segment display module with Gravity I2C interface. This module can display numbers, basic characters, and supports 16 levels of brightness adjustment — ideal for clocks, counters, dashboards, and data readouts in Arduino and Raspberry Pi projects. The Gravity connector makes w...

SKU: DF-DRI0056 · MPN: DRI0056

This Gravity haptic driver module is built for Linear Resonant Actuators (LRAs), turning simple I2C commands into crisp tactile feedback for interactive projects. It is powered by the TM6605 driver chip and supports LRA resonant frequencies from 140Hz to 220Hz.The module includes 44 built-in vibr...

SKU: DF-SEN0130

The Gravity MQ5 gas sensor is highly sensitive to LPG, natural gas, and town gas, with lower sensitivity to alcohol, cooking fumes, and cigarette smoke. The analogue output is proportional to gas concentration, and sensitivity can be adjusted via the on-board potentiometer. Gravity interface for ...

SKU: DF-SEN0189

The Gravity Analog Turbidity Sensor measures water clarity by detecting the level of suspended particles. It works by measuring light transmittance and scattering rate, which change with the amount of total suspended solids (TSS) in the water. The sensor provides both analogue (0–4.5V) and digit...

SKU: DF-SEN0134

The Gravity MQ-9 gas sensor detects carbon monoxide (CO) and combustible gases including methane and propane. It uses a semiconductor SnO2 sensing element that cycles between high and low temperatures — detecting CO at low temperature (1.5V) and combustible gases at high temperature (5.0V). With...

SKU: DF-SEN0239

A digital infrared proximity sensor with adjustable detection range from 0 to 200 cm. Outputs a simple digital signal — HIGH when an obstacle is detected, LOW when clear. The detection threshold is adjustable via a rear-mounted screw, making it easy to tune for different applications. Features t...

SKU: DF-FIT0916-F · MPN: FIT0916-F

These labelled jumper cables are designed to make Gravity project wiring easier to follow, especially when a build has several similar connections. Each cable carries I2C/UART pin labels so you can identify power, ground, clock/receive and data/transmit lines without relying only on wire colour o...

SKU: DF-DFR0785-W · MPN: DFR0785-W

This Gravity LED button is a simple illuminated push button with a transparent cap, designed for interactive Arduino and micro:bit projects. When the button is pressed, the internal white LED turns on to provide clear visual feedback.The module behaves like a basic digital switch: when pressed do...

SKU: DF-DFR0030

A digital capacitive touch sensor from DFRobot's Gravity series. It detects touch through the same capacitive sensing technology used in smartphones — even through thin cloth or paper. The sensor outputs a digital high/low signal, making it a simple drop-in replacement for mechanical buttons in A...

SKU: DF-DFR0554

The Gravity I2C 16×2 LCD features RGB font colours on a black background, allowing you to display text in any of 16 million colour combinations. Using the Gravity I2C interface, only two data lines are needed for both communication and backlight control. The display supports 2 rows of 16 charact...

SKU: DF-TEL0140-1

This Gravity wireless switch kit provides simple 433 MHz RF communication between a transmitter and receiver module. Based on digital signal transmission, it offers strong wall penetration, ultra-low standby power consumption, and compatibility with any controller that can read and write digital ...

SKU: DF-SEN0665 · MPN: SEN0665

This compact Gravity module brings Bosch BMP581 pressure and temperature sensing to microcontroller projects that need stable altitude or environmental readings. It is designed for applications such as drone altitude hold, indoor navigation, weather logging and hiking altimeters.The board support...

SKU: DF-DFR0785-R · MPN: DFR0785-R

This compact illuminated push-button module is designed for interactive electronics and quick prototyping. A transparent cap sits over an internal red LED, giving instant visual feedback when the button is pressed.The module provides a simple digital output for microcontroller input detection: wh...

SKU: DF-DFR0760

The Gravity Speech Synthesis Module converts text to spoken audio in English and Chinese, including mixed-language content. It connects via I2C or UART using the standard Gravity interface and includes a built-in speaker, so no additional audio hardware is needed. The module supports text contro...

SKU: DF-DFR1229 · MPN: DFR1229

This GP8600 module is a high-precision digital-to-analogue converter for connecting logic-level microcontrollers to industrial-style analogue control inputs. It accepts I2C or PWM signals and converts them for applications such as 0-5V, 0-10V and 4-20mA control.It is designed for automation and c...

SKU: DF-DFR0469

A high-precision I2C real-time clock (RTC) module from DFRobot's Gravity series, based on the SD2405AL chip. It features an internal rechargeable battery that keeps time for 5–8 years without external power, making it ideal for data logging, alarm clocks, and any project that needs reliable timek...