All Products

SKU: PL-968

The 0.100″ (2.54 mm) Shorting Block is a removable jumper with a closed-top blue housing, designed to bridge two adjacent pins on a standard 0.1″ pitch male header. Shorting blocks are essential for configuring hardware settings, selecting operating modes, and enabling or disabling features on PC...

SKU: PL-970

The 0.100″ (2.54 mm) Shorting Block is a removable jumper with a closed-top black housing, designed to bridge two adjacent pins on a standard 0.1″ pitch male header. Shorting blocks are essential for configuring hardware settings, selecting operating modes, and enabling or disabling features on P...

SKU: PL-972

A 300mm (12″) 6-conductor ribbon cable with female 2×3 IDC connectors on each end. Designed to plug into standard 0.1″ (2.54mm) 2×3 shrouded box headers, and also compatible with 0.1″ male header pins. Key Features IDC Connectors – Female 2×3 IDC connector on each end 6 Conductors – Flat ribb...

SKU: AF-3232

Add long-range LoRa radio to any Feather board with the Adafruit LoRa Radio FeatherWing. Built around the SX127x LoRa module, this add-on provides kilometre-range packet radio communication at 433 MHz — perfect for sensor networks, remote monitoring, and bridging to the Internet via a WiFi or cel...

SKU: AF-3231

Add long-range LoRa radio to any Feather board with the Adafruit LoRa Radio FeatherWing. Built around the SX127x LoRa module, this add-on provides kilometre-range packet radio communication at 900 MHz (tuneable to 868 MHz or 915 MHz) — perfect for sensor networks, remote monitoring, and bridging ...

SKU: AF-266

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are a little over 6" (150mm) long and come in a 'strip' of 40 (4 pieces of each of ten colors). They have 0.1" sockets on either end and fit cleanly next to each other on standard-pitch 0.1" (2.54...

SKU: AF-3141

Our Raw F/F Jumper Wires are perfect for making custom jumper wire sets for wire harnesses or jumpering between headers on PCB's. These premium jumpers are a little over 6" (150mm) long and come in a 'strip' of 40 (4 pieces of each of the ten colors).  The 0.1" spacing raw sockets on eith...

SKU: AF-2934

A custom gamepad PCB designed for the PiGRRL Zero project. This PCB dramatically cuts build time by providing a ready-made board — just solder in 6mm tactile switch buttons and wire up the header pins to your Pi Zero. Ideal for makers who already have the rest of the PiGRRL Zero parts or are doi...

SKU: AF-206

A 150mm (6″) jumper cable with 6 conductors at 0.1″ (2.54mm) spacing. Features female socket connectors on both ends for quick plug-in connections to header pins. Key Features Socket-to-Socket – Female connectors on both ends 6 Conductors – 0.1″ (2.54mm) pitch spacing 150mm Length – Compact ...

SKU: PL-2128

The Black Edition of the A4988 stepper motor driver carrier features a four-layer PCB for better thermal performance, allowing the A4988 to deliver approximately 20% more current than the standard two-layer (green) version. It is a drop-in replacement for the original carrier in most applications...

SKU: PL-2134

This is a breakout board for TI’s DRV8834 microstepping bipolar stepper motor driver. It has a pinout and interface that are nearly identical to those of our A4988 carriers, so it can be used as a drop-in replacement for those boards in many applications. The DRV8834 operates from 2.5–10.8&nbsp...

SKU: PL-1164

This 15cm (6") cable features a 2-pin female JST XH-style connector with 2.5mm pitch. The two 26AWG conductors (red and black) are twisted together to reduce electrical noise, with unterminated ends that can be cut to length for your application. The 2.5mm pitch is close enough to 0.1" (2.54mm) ...

SKU: SF-PRT-00114

A through-hole soldering kit that builds into a compact breadboard power supply. It accepts a DC barrel jack input and outputs a selectable 5 V or 3.3 V regulated supply via 0.1" (2.54 mm) header pins that plug directly into breadboard power rails. The board features an on/off switch, a 3.3 V / ...

SKU: SF-WRL-11697

This is the SparkFun XBee Explorer Dongle unit for the Digi XBee module line. With the XBee Explorer Dongle you can plug the unit directly into your USB port and have it act as a gateway between your computer and the XBee. No cables needed! This unit works with all XBee modules including the Seri...

SKU: SF-WRL-11812

This is a simple to use, USB to serial base unit for the Digi XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, attach a mini USB cable, and you will have direct access to the serial and programm...

SKU: PL-1336

The Pololu Wixel is a general-purpose programmable module featuring a 2.4 GHz radio and USB. You can write your own software or load precompiled, open-source apps onto the TI CC2511F32 microcontroller at the heart of the Wixel, turning it into a wireless serial link, data logger, or whateve...

SKU: DF-DFR0224

The Arduino Screwless Terminal Shield breaks out all Arduino Uno-compatible header pins to spring-loaded push-in terminal blocks. Press the lever, insert your wire, and release — no screwdriver needed. The shield stacks with standard Arduino shields, so you can add additional boards on top. Key ...

SKU: AF-2809

The Adafruit LIS3DH is a popular, low-power triple-axis accelerometer breakout packed with features typically found only on higher-end sensors. With selectable measurement ranges, multiple interface options, and built-in motion detection, it's one of the most versatile accelerometers available at...

SKU: SF-PRT-09044

A standard 2-pin jumper shunt used to create an electrical connection between two adjacent pin headers. Commonly used to configure settings on development boards, select operating modes, or bridge header pins on PCBs. Specifications Type – 2-pin jumper (shunt) Pitch – 2.54 mm (0.1") standard ...

SKU: DF-FIT0209

A 4-pin female housing connector with a standard 2.54 mm (0.1") pitch. Use these to create custom cables that mate with 0.1"-spaced header pins on breakout boards, sensors, and development boards. Note: Does not include metal crimp pins, which are required and sold separately. Specifications ...