All Products

SKU: SF-DEV-13672

If you’re ready to step your Arduino game up from older 8-bit/16MHz microcontrollers, the SparkFun SAMD21 Dev Breakout is a great landing spot. The SparkFun SAMD21 Dev Breakout is an Arduino-sized breakout for the Atmel ATSAMD21G18, a 32-bit ARM Cortex-M0+ processor with 256KB flash, 32KB SRAM...

SKU: SF-WRL-13711

This is the SparkFun ESP8266 Thing Dev Board – a development board that has been solely designed around the ESP8266, with an integrated FTDI USB-to-Serial chip. The ESP8266 is a cost-effective, and very capable WiFi-enabled microcontroller. Like any microcontroller, it can be programmed to blink ...

SKU: SF-BOB-13717

This is the SparkFun Pi Wedge, a small board that connects to the 40-pin GPIO connector on the Raspberry Pi and breaks the pins out to breadboard-friendly arrangement and spacing, and even adds a couple of decoupling capacitors on the power supply lines. The “Wedge” also makes the initial b...

SKU: SF-DEV-13743

The SparkFun Level Shifting microSD Breakout is quite similar to the SparkFun microSD Transflash Breakout, but with the included level shifting hardware, this board allows you to utilize a microSD card at Arduino’s SD library’s top speed on a 5V system. With this small breakout board, that is not...

SKU: SF-DEV-13746

The SparkFun Beefy 3 is an FTDI Basic Breakout board based on the FT231X USB-to-serial IC. Unlike standard FTDI breakouts, it features an AP2112K voltage regulator capable of supplying up to 600mA at 3.3V — enough to power a 3.3V project directly from the board's USB connection. The 6-pin header...

SKU: SF-SEN-13763

A low-cost, highly accurate digital humidity and temperature sensor breakout board based on the Silicon Labs Si7021. Communicates over I²C with just two data lines, providing relative humidity and precise temperature readings for environmental monitoring projects. The breakout includes built-in ...

SKU: SF-COM-11629

A smart 4-digit 7-segment display that combines a classic white LED display with an onboard ATmega328 microcontroller. Instead of wiring up dozens of pins, you control the entire display over Serial TTL, SPI, or I2C — using just a few connections. The ATmega328 comes pre-loaded with the Arduino ...

SKU: SF-PRT-13777

The SparkFun Battery Babysitter is an all-in-one single-cell Lithium Polymer (LiPo) battery manager. It’s half battery charger, half battery monitor, and all you’ll ever need to keep your battery-powered project running safely and extensively. The Battery Babysitter features a pair of Texas Inst...

SKU: SF-WRL-11697

This is the SparkFun XBee Explorer Dongle unit for the Digi XBee module line. With the XBee Explorer Dongle you can plug the unit directly into your USB port and have it act as a gateway between your computer and the XBee. No cables needed! This unit works with all XBee modules including the Seri...

SKU: SF-KIT-13815

Your 5V system can wield great power with this big, beefy relay board. How does 20A on the NC contacts and 10A on the NO contacts at 220VAC sound? The SparkFun Beefcake Relay Control Kit contains all the parts you need to get your high-power load under control. Only minimal assembly is required! ...

SKU: SF-BOB-13830

The CY7C65213 USB to UART serial breakout is designed to provide users with a means to access all available I/O pins on the IC, and to provide a 6-pin UART header that is compatible with other SparkFun breakout boards. This breakout has a microUSB connector and other support circuitry to get t...