Sensors & Input

SKU: EF-EF04092 | Brand: ElecFreaks

The Octopus Light Sensor Brick reads the ambient light level of its surrounding environment and outputs an analog signal. The 3-pin GVS connector makes it easy to plug into micro:bit expansion boards, Arduino, and oth...

SKU: AF-1083 | Brand: Adafruit

Add high-speed analog-to-digital conversion to any microcontroller with the ADS1015 breakout. This 12-bit ADC delivers 3,300 samples per second over I2C, with four single-ended or two differential input channels and a...

SKU: LB-LS0239 | Brand: Little Bird

This e-textiles ambient light sensor uses the TEMT6000 phototransistor to detect light levels. Designed for wearable electronics, it features a compact 20 mm round PCB that's only 0.8 mm thick — thin enough to sew int...

SKU: SF-SEN-14262 | Brand: SparkFun

The SparkFun Sound Detector is a small and very easy-to-use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of the presence of sound...

SKU: SF-SEN-09196 | Brand: SparkFun

This basic piezo sensor from Measurement Specialties is often used for flex, touch, vibration and shock measurements. A small AC and large voltage (up to +/-90V) is created when the film moves back and forth. A simple...

SKU: SF-COM-09032 | Brand: SparkFun

This is a joystick very similar to the ‘analog’ joysticks on PS2 (PlayStation 2) controllers. Directional movements are simply two potentiometers - one for each axis. Pots are ~10k each. This joystick also has a se...

SKU: DF-DFR0051 | Brand: DFRobot

The Analog Voltage Divider V2 can detect the supply voltage from 0.0245V to 25V. This module is based on resistor divider principle. The voltage detection module allows the input voltage to reduce 5 times. As the A...

SKU: SF-DEV-13116 | Brand: SparkFun

The SparkFun Spectrum Shield splits a stereo audio input into 7 frequency bands per channel using two MSGEQ7 graphic equaliser ICs. Read the amplitude of each band via your Arduino's ADC to create sound-reactive proje...

SKU: AF-519 | Brand: Adafruit

Measuring stretch forces isn't easy - unless you have some conductive rubber cord! This cord is 2mm diameter, and 1 meter long, made of carbon-black impregnated rubber. Usually this material is used for EMF gasketing,...

SKU: SF-BOB-12758 | Brand: SparkFun

The SparkFun Electret Microphone Breakout pairs a small electret microphone capsule with a 60× OPA344 op-amp preamplifier, making it easy to detect sound with a microcontroller's analogue-to-digital converter. Pick up...

SKU: AF-3245 | Brand: Adafruit

Thermocouples are best used for measuring temperatures that can go above 100°C. This is a bare wires stainless-steel tip probe which can measure air or surface temperatures. Most inexpensive thermocouples have a vi...

SKU: DF-DFR0034 | Brand: DFRobot

This is a new Arduino compatible Analog Sound Sensor. Sound Sensor is typically used in detecting the loudness in ambient, the Arduino can collect its output signal and actuate accordingly. You may use it to make some...

SKU: DF-SEN0209 | Brand: DFRobot

This is an Arduino compatible piezo film vibration sensor. It is made up of flexible piezo film and converter board. The sensor is able to detect vibration, flexibility, impact and touch. The film is a flexible compo...

SKU: SF-BOB-19389 | Brand: SparkFun

The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the SPH8878LR5H-1 analog microphone from Knowles. This board features an OpAmp to bring the output of the microphone to a usable level, allowing ...

SKU: SF-SEN-19018 | Brand: SparkFun

An Infrared detector is a detector that reacts to infrared (IR) radiation. These simple devices operate at 940nm and work well for generic IR systems including remote control and touch-less object sensing. Using a sim...

SKU: EC-DPI32110W | Brand: Elecrow

ESP32-S2-WROVER and ESP32-S2-WROVER-I use ESP32-S2 chip. The ESP32-S2 chip is equipped with an Xtensa® 32-bit LX7 single-core processor with a working frequency of up to 240 MHz. The user can turn off the power of the...

SKU: EF-EF04088 | Brand: ElecFreaks

The Octopus 2 Channel Tracking Module uses two pairs of reflective infrared diodes to detect black lines on a surface. Designed for line-following smart cars, it lets you create custom black track layouts and program ...

SKU: AF-4543 | Brand: Adafruit

A 20 kg strain gauge load cell with four wires, featuring a metallic foil gauge bonded with epoxy to a solid aluminium bar. The aluminium constrains deflection and protects the gauge from damage. Mount one end to a fi...

SKU: AF-4516 | Brand: Adafruit

The Feather nRF52840 Sense takes the popular Feather nRF52840 Express and adds a suite of on-board environmental and motion sensors. It features Bluetooth Low Energy, native USB, CircuitPython and Arduino support, plu...

SKU: EC-ARS03218S | Brand: Elecrow

The board is designed for beginners in Arduino, with various components available that makes you build more than 10 projects easily. You won’t have to solder or connect anything at all, just plug it in a shield and st...