All Products

SKU: DF-DFR0785-W · MPN: DFR0785-W

This Gravity LED button is a simple illuminated push button with a transparent cap, designed for interactive Arduino and micro:bit projects. When the button is pressed, the internal white LED turns on to provide clear visual feedback.The module behaves like a basic digital switch: when pressed do...

SKU: DF-SEN0628 · MPN: SEN0628

This compact 3D depth-sensing module sits between a simple single-point distance sensor and a full depth camera. It uses an 8×8 Time-of-Flight matrix to return depth data from 64 points, giving your robot or interactive project a much better sense of what is in front of it.Onboard firmware runs o...

SKU: DF-SEN0656 · MPN: SEN0656

The CT1780 is a cold-junction compensated amplifier for K-Type thermocouples, designed to make extreme temperature measurement easier to add to microcontroller projects. It digitises the tiny thermocouple signal and provides temperature readings with 0.25℃ resolution over a very wide measurement ...

SKU: DF-DRI0056 · MPN: DRI0056

This Gravity haptic driver module is built for Linear Resonant Actuators (LRAs), turning simple I2C commands into crisp tactile feedback for interactive projects. It is powered by the TM6605 driver chip and supports LRA resonant frequencies from 140Hz to 220Hz.The module includes 44 built-in vibr...

SKU: DF-SEN0678 · MPN: SEN0678

This Gravity air quality module uses Sensirion’s STCC4 gas sensing chip to directly measure carbon dioxide with the thermal conductivity measurement principle. It is designed for compact, cost-effective indoor monitoring nodes where stable CO₂ readings are needed without complex hardware integrat...

SKU: DF-SEN0451 · MPN: SEN0451

This industrial Gravity kit measures electrical conductivity in aqueous solutions, helping you evaluate water quality by tracking dissolved content or salinity. It is suited to hydroponics, aquaculture and environmental water monitoring where long-running measurements are needed.The pro probe is ...

SKU: DF-TEL0179 · MPN: TEL0179

Add LTE CAT1 connectivity to IoT projects and development boards with this Air780E communication module from DFRobot. It supports LTE-FDD B1/B3/B5/B8 and LTE-TDD B34/B38/B39/B40/B41 bands, making it suitable for deployments in China, India, Southeast Asia and other supported regions.The module pr...

SKU: DF-DFR0076

This Gravity analog flame sensor detects fire and infrared light sources in the 760–1,100 nm wavelength range. With a 60° detection angle and analogue output proportional to flame distance, it's widely used in firefighting robots, fire alarm projects, and other safety applications. The Gravity i...

SKU: DF-FIT0514

These wire offers you the best way to connect sensors and actuators to your LattePanda! They are specially designed for LattePanda and DFRobot Gravity Sensors. It compatible with a wide range of Gravity sensors and is easy to connect thanks to the unique anti-reverse-polarity design. It incl...

SKU: DF-SEN0231

The Formaldehyde (HCHO) sensor is an Arduino & Raspberry Pi compatible module, which is the ideal solution for indoor air quality monitor. This is a HCHO(CH2O) sensor module. It can be used to measure HCHO in air. Through it, you can know the air quality. This sensor module is widely used ...

SKU: DF-DFR0053

This arduino Slide Position Sensor is based on straight-slip slide potentiometer sensor. The sensor is able to give provide the position of the slider which is often considered as a linear potentiometer . The sensor includes two analog outputs to allow the user to average the values and m...

SKU: DF-DFR0030

A digital capacitive touch sensor from DFRobot's Gravity series. It detects touch through the same capacitive sensing technology used in smartphones — even through thin cloth or paper. The sensor outputs a digital high/low signal, making it a simple drop-in replacement for mechanical buttons in A...

SKU: DF-SEN0219

The concentration of carbon dioxide (0.03% usuallly) is related to daily life. Recently, there's a study showing that the atmospheric CO2 content has reached 0.0385% (385 ppm) which is the highest value since 2.1 million years. The raise of atmospheric CO2 content to some extent results in gl...

SKU: DF-SEN0217

INTRODUCTION   The Gravity Water Flow sensor measures the rate of a liquid flowing through it. The YF-S201 water flow sensor consists of a plastic valve body, flow rotor and hall effect sensor. It is usually used at the inlet end to detect the amount of flow. When liquid flows throug...

SKU: DF-SEN0177

The Gravity Laser PM2.5 Air Quality Sensor uses laser scattering to measure suspended particulate matter concentrations in the air. It detects particles from 0.3 to 10 µm in diameter and outputs digital concentration data via a serial interface — ideal for building air quality monitors, weather s...

SKU: DF-DFR0029-B

The Gravity Digital Push Button (Blue) is a simple momentary push button module designed for the DFRobot Gravity interface. It features an onboard LED indicator, immersion gold PCB surface, and a coloured button cap. A "D" marking on the board identifies it as a digital sensor for quick wiring re...

SKU: DF-DFR0017

The DFRobot Relay Module is a standard relay used with a controller board to interface external electrical circuits or modules. Some of the most common applications with Arduino are: Home lighting, electrical appliances of high power and other equipments. The modular design makes it easy to in...

SKU: DF-DFR0521

The micro:bit Expansion Board for Boson is a carry-on board that connects to the BBC micro:bit via edge connector, replacing crocodile clips with six keyed 3-pin sockets. It is compatible with DFRobot's Boson and Gravity modularised electronic modules, giving access to hundreds of digital and ana...

SKU: DF-SEN0257

The Gravity Analog Water Pressure Sensor measures water or gas pressure and outputs a linear 0.5–4.5 V analogue signal proportional to the applied pressure (0–1.6 MPa). Using the DFRobot Gravity 3-pin interface, it connects directly to Arduino and other 5 V microcontrollers for easy integration i...

SKU: DF-DFR0523

Gravity: digital peristaltic pump is a new product developed by DFRobot. This is a new member of our water quality monitoring devices. It is an actuator for the liquid system. DFRobot peristaltic pump integrates a PPM motor driver on the pump, this is a Gravity interface (PH2.0-3P) motor...