This is 12 meters of smooth conductive thread spun from stainless steel fiber and wound on a plastic bobbin. Use it to sew up all of your e-text...
View full details
This conductive material (also known as "Velostat" or "Linqstat") is a nice addition for your wearable/sensor hacking toolkit. It's pressure-sen...
View full detailsLight up your E-Textile projects with this set of 5 E-Textile Compatible LED modules. With a working voltage of 3V - 5V and a current of 40mA, thes...
View full details
With our fun assortment of conductive materials, cosplay and wearables have never been easier to craft! This Conductive Nylon tape goes great ...
View full detailsThis is a simple single unit YELLOW E-Textile LEDEach unit can be sewn into fabric. Various input, output, power and sensor boards are available. T...
View full detailsThis is a simple single unit RED E-Textile LEDEach unit can be sewn into fabric. Various input, output, power and sensor boards are available. They...
View full detailsThis is a simple single unit GREEN E-Textile LEDEach unit can be sewn into fabric. Various input, output, power and sensor boards are available. Th...
View full details
Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels —...
View full details
A small, but mighty power supply. This board was designed to be as small and inconspicuous as possible. Pop in a AAA battery, flip the power switch...
View full details
With our fun assortment of conductive materials, cosplay and wearables have never been easier to craft! This Conductive Nylon tape goes great ...
View full detailsA sewable tri-colour RGB LED module designed for e-textiles and wearable electronics. By grounding the red, green, or blue channel pins individuall...
View full detailsA sewable white LED module designed for e-textile projects. This single-unit LED can be stitched directly into fabric using conductive thread, maki...
View full detailsA single yellow-green LED module designed for e-textiles projects. Each unit features sewable tabs so it can be stitched directly into fabric using...
View full details
This 316L stainless steel conductive yarn sits between a thick thread and a thin yarn in weight. Its high conductivity and soft, flexible texture m...
View full details
EagLED is Little Bird Electronics' wearable development kit. It's a complete Arduino compatible microcontroller that has LEDs, Light Sensor, Pus...
View full detailsThis is a three axis accelerometer designed for E-Textiles. Based on the ADXL335 MEMS accelerometer from Analog Devices, this Accelerometer can...
View full detailsThis is a simple single unit ORANGE E-Textile LEDEach unit can be sewn into fabric. Various input, output, power and sensor boards are available. T...
View full details
This is a simple slide switch for the LilyPad. Use it as a simple ON/OFF switch, or to control LEDs, buzzers, sensors, etc. The swtiches on each bo...
View full details
A 13.3-inch e-Paper display HAT for the Raspberry Pi, featuring a 960×680 resolution black and white panel with over 170° viewing angle. The e-ink ...
View full details
A pack of five pink LilyPad LEDs designed for wearable electronics and e-textile projects. The LEDs come attached to one another on a snap-apart st...
View full details
A 20 mm coin cell battery holder designed for CR2032 batteries. The holder features a pop-in, pop-out mechanism for easy battery changes, and the m...
View full details
These handy little screwdrivers can be used with our E-Textile boards to add and remove the M1.4 screws to access the coin cell battery.The screwdr...
View full detailsThis is a simple single unit BLUE E-Textile LEDEach unit can be sewn into fabric. Various input, output, power and sensor boards are available. The...
View full details
Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels —...
View full details
