All Products

SKU: PL-5049

The Motoron M2H family of dual high-power motor controller add-on boards makes it easy to control up two bidirectional, brushed DC motors with a compatible Raspberry Pi (Model B+ or newer). The M2H controllers are designed to stack on top of a Raspberry Pi (Model B+ or newer), similar to a HAT...

SKU: DF-DFR1063 · MPN: DFR1063

The Romeo Mini ESP32-C3 is a compact robot control board with an onboard ESP32-C3 module providing Wi-Fi and Bluetooth 5 dual-mode communication. It features two channels of 1.7A motor drivers, servo control, and 9 Gravity-compatible I/O interfaces — all in a tiny 47mm × 38.5mm form factor. A bu...

SKU: AF-1750

The Synthetos gShield (formerly grblShield) V5 is a 3-axis CNC stepper motor driver shield for Arduino. Designed as a complete hardware companion for the grbl CNC motion control firmware, it turns an Arduino Uno into a capable CNC controller for mills, routers, laser cutters, and other motion-con...

SKU: LB-LR0149

The EasyDriver is a simple stepper motor driver board based on the Allegro A3967 IC. It accepts a digital step/direction input (3.3 V or 5 V logic) and drives bi-polar stepper motors (4, 6, or 8 wire) at any voltage within the 7–30 V supply range. The board features adjustable current control fr...

SKU: AF-5757

The Mosfetti by Monk Makes is a compact 4-channel MOSFET switch designed for maker projects. Each channel can drive up to 2 A of low-side switching at up to 16 V DC, making it perfect for controlling relays, solenoids, LED strips, pumps, and motors from a microcontroller. Supplied as a PCB with ...

SKU: AF-4280

The Adafruit DC & Stepper Motor Bonnet drives up to 4 DC motors or 2 stepper motors from your Raspberry Pi, with full PWM speed control. It uses a dedicated PWM driver chip over I2C, so only two pins (SDA/SCL) are needed — leaving the rest free for other I2C devices or HATs. The TB6612 MOSFET mo...

SKU: EC-ARS27361T

This motor shield uses dual TB6612 MOSFET drivers and a PCA9685PW I2C PWM controller to drive up to 4 DC motors or 2 stepper motors from an Arduino or compatible board. All motor control and speed management is handled via the I2C bus, freeing up digital pins for other uses. The stackable design...

SKU: AF-807

Run four solenoids, two DC motors or one bi-polar or uni-polar stepper with up to 600mA per channel using the L293D. These are perhaps better known as "the drivers in our Adafruit Motorshield". If you accidentally damaged the drivers in a shield, you can use one of these puppies to replace it....

SKU: AF-3093

The Adafruit CRICKIT for Circuit Playground Express is a robotics and electronics driver board that bolts directly onto a Circuit Playground Express. It adds motor drivers, servo outputs, capacitive touch inputs, NeoPixel control, and an audio amplifier — all managed over I2C via the Adafruit see...

SKU: PL-5063

The Motoron M1U256 Single I²C Motor Controller offers a compact solution for controlling two DC motors using a UART serial interface. Multiple Motoron controllers can be connected to the same serial bus, making it easy to expand a system with additional motors. The M1U256 operates from 4.5 V to 4...

SKU: AF-4489

Run two solenoids, or a single DC motor with up to 800mA per channel using the super-simple L9110H H-bridge driver. This bridge chip is an 8 DIP package so it's easy to fit onto any breadboard or perfboard.Each chip contains one full H-bridges (two half H-bridges). That means you can drive 2 sole...

SKU: SF-ROB-10507

The Quadstepper motor driver board allows you to control up to 4 bipolar stepper motors simultaneously using logic level IO pins. Each motor driver has an output drive capacity of 35V and 1Amps. The board is capable of driving motors in full, half, quarter, eight, and sixteenth-step modes. The lo...

SKU: EF-EF05043

The Nezha Breakout Board is a feature-packed expansion board for the micro:bit, designed with classroom use in mind. It integrates 4 servo drivers, 4 motor drivers, and 7 sensor ports — all using RJ11 connectors with foolproof anti-reversal design, so students can plug in confidently without dama...

SKU: AF-2348

The Adafruit DC & Stepper Motor HAT drives up to 4 DC motors or 2 stepper motors from your Raspberry Pi, with full PWM speed control. It uses a dedicated PWM driver chip over I2C, so only two pins (SDA/SCL) are needed — leaving the rest free for other I2C devices or HATs. The TB6612 MOSFET motor...

SKU: DF-DRI0040

INTRODUCTION This is a ultra compact size Dual-H-Bridge dc motor driver (Based on HR8833), which could drive two way 1.5A DC brush motors up to 10V . It has the same footprint as your thumbnail suitable for projects with limited spaces. Both sides of the module are ...

SKU: PR-PIM618

A compact 4 channel motor+encoder controller, powered by RP2040. It has RGB and per-motor indicator LEDs plus built in voltage and current sensing. Motor 2040 is a standalone motor controller for driving motors with encoders attached. Encoder motors can provide feedback to the controller, enabli...

SKU: EC-DTS09534M

This motor/ servo shield is for Micro: bit, it provides a simple way to add motor driving capability to a micro: bit. The shield can drive 2 motors, 2 servos, and allow the motors to be driven with forward, reverse, stop control. It’s easy to add the motor to the shield, and there is an integrate...

SKU: SF-ROB-12859

The Big Easy Driver is a stepper motor driver board for bipolar stepper motors up to 2 A per phase, based on the Allegro A4988 driver chip. Designed by Brian Schmalz, it's the successor to the popular Easy Driver board. It defaults to 16-step microstepping mode and includes onboard 5 V and 3.3 V...

SKU: WS-25514

The Bus Servo Adapter (A) is a compact driver board that integrates power supply and control circuitry for ST/SC series serial bus servos. It supports controlling up to 253 servos simultaneously over a single UART channel, with position, speed, torque, and operating mode feedback from each servo....

SKU: LB-OWL-HBRIDGE

Using the powerful L298N Dual Motor Driver，this module allows full control of two DC Motors or one stepper-motor. Screw Terminals for easy connections；LEDs show power and output status. Requires six digital inputs. Has 4 mounting holes. Specification: Chip: L298N  Maximum Output Curre...