All Products

SKU: DF-DFR0785

A pack of five LED-illuminated push buttons in the DFRobot Gravity format. Each button lights up a different colour (red, yellow, green, blue, and white) when pressed, providing clear visual feedback. The digital output goes HIGH when pressed and LOW when released, making them simple to read with...

SKU: DF-DFR0029-R

Press to release pleasure! Our redesigned digital push buttons come with LED, immersion gold surface, and bright colored hats. A captital D at left corner indicates that it is a digital sensor. An illustration of button painted in the back notifying its function. Pressing it is a real fun, esp...

SKU: DF-DFR0021-R

A simple red LED module with a Gravity 3-pin digital interface for plug-and-play connection to Arduino and other microcontrollers via a Gravity IO Expansion Shield. Ideal for beginners learning digital output control. Key Features Gravity Interface – 3-pin plug-and-play connection Digital Con...

SKU: DF-DFR0061

The Gravity Joystick Module V2 provides two-axis analogue control (X and Y) plus a digital push-button switch. Connect the two analogue outputs and one digital output to your Arduino or other microcontroller for intuitive directional input — ideal for robot control, menu navigation, and game proj...

SKU: DF-DFR0785-W · MPN: DFR0785-W

This Gravity LED button is a simple illuminated push button with a transparent cap, designed for interactive Arduino and micro:bit projects. When the button is pressed, the internal white LED turns on to provide clear visual feedback.The module behaves like a basic digital switch: when pressed do...

SKU: DF-TEL0140-1

This Gravity wireless switch kit provides simple 433 MHz RF communication between a transmitter and receiver module. Based on digital signal transmission, it offers strong wall penetration, ultra-low standby power consumption, and compatibility with any controller that can read and write digital ...

SKU: DF-DFR1036 · MPN: DFR1036

A 1-channel DAC module that converts a PWM signal from any microcontroller into a precise 0–5V or 0–10V analogue voltage output. Built around the GP8101S chip with 8-bit resolution and 0.2% accuracy, it's ideal for driving standard 0–10V or 0–5V controlled devices in automation projects — lights,...

SKU: DF-KIT0111

The Gravity Starter Kit for Arduino is a plug-and-play electronics toolkit designed for beginners and makers getting started with the Arduino platform. It includes a DFRduino UNO R3 microcontroller (fully compatible with Arduino UNO) along with 12 popular sensors and components from DFRobot's Gra...

SKU: DF-DFR0473

Introducing the Gravity Digital Relay Module - the latest addition to DFRobot's Gravity series! This module is a little different to the other relays in our store - not only is it compatible with 5V Arduino boards, but also with Raspberry Pi, BBB (BeagleBoard Black), mbed, Intel Joule, Arduino 10...

SKU: LB-LS3381-R

A 12 mm panel-mount momentary push button with a smooth dome-shaped cap in red, pre-wired with 20 cm red and black leads for easy connection. Normally open — pressing the button closes the contacts. Key Features Pre-Wired – 20 cm red and black leads attached, no soldering required Momentary A...

SKU: DF-DFR0031-R

Piranha LED light module (Red), and special sensors Arduino board and ambient light sensor extension combination, can be used in the interaction with the light works. When the LED light module connected to Arduino, the digital pin (LOW on, HIGH off) is used to control it. The brightness of LE...

SKU: DF-DFR0423

INTRODUCTION This module is a self-locking switch. Press the button to turn it to the "on" state and press it again to turn it to the "off" state. The board has immersion gold plating and is compatible with the "gravity" 3-pin interface making it easy to connect to a...

SKU: DF-DFR0979

The Gravity CH423 I2C 24 Digital IO Expansion Module extends your microcontroller with 24 additional digital output/input pins over a standard I2C connection. Based on the CH423 chip, it provides 8 GPIOs with interrupt support and 16 dedicated GPOs. The built-in current drive circuit delivers up...

SKU: DF-SEN0239

A digital infrared proximity sensor with adjustable detection range from 0 to 200 cm. Outputs a simple digital signal — HIGH when an obstacle is detected, LOW when clear. The detection threshold is adjustable via a rear-mounted screw, making it easy to tune for different applications. Features t...

SKU: LB-LR0589-RED

A 12 mm panel-mount momentary push button with a smooth dome-shaped cap in red. Normally open — pressing the button closes the contacts. The dome design provides a satisfying tactile feel and sits flush with the panel surface. Key Features Momentary Action – Normally open, closes on press 12 ...

SKU: DF-KIT0018

The DFRobot Gravity Intermediate Kit for Arduino takes you beyond the basics with a comprehensive set of sensors, modules, and an Arduino-compatible board. Starting with simple LED projects and progressing to more complex builds like a mini electronic drum kit, sound-activated LED, and digital di...

SKU: SF-COM-11971

This is a perfect choice if you are in need of a heavy duty push button! These metal push buttons are a very tough, small, panel-mount latching switch with an illuminated red LED ring. It is a SPDT with 16mm threading and 1mm pitch. This button is perfect for basic On/Off functions. Overall le...

SKU: LB-TACTILE-RED

A 25-pack of red tactile push buttons, perfect for prototyping and project builds. Each button features a removable coloured cap and fits directly into standard breadboards for quick, solder-free connections. Key Features 25 Buttons Included – Bulk pack for multiple projects Removable Red Cap...

SKU: DF-DFR1184 · MPN: DFR1184

The Gravity 0–10V ADC Module is a high-precision dual-channel analogue-to-digital converter designed to interface industrial-grade 0–10V sensors with microcontrollers and Linux-based systems. Built on the Texas Instruments ADS1115, it delivers 15-bit resolution (0.375 mV per step) with ±2 mV accu...

SKU: DF-KIT0011

INTRODUCTION If you want to start playing with sensors, this sensor kit for arduino will be the perfect choice for you to get started. It comes with bundle of the most popular DFRobot sensors such as light sensors, gas sensors, sound sensors, touch sensors, distance sens...