All Products
AI Overview
For an Electric Brick / 4‑wire “fully buckled” cable request, the closest matches are 4‑pin latching sensor cables/connectors commonly used for I2C/UART modules:
4‑wire latching cable options (most likely match)
- Grove Cable Pigtail - 2mm pitch 100mm long ($2.15) — 4‑wire Grove connector to bare wire ends (good when you need a “pigtail” to screw terminals or custom wiring).
- 2.0mm Pitch 4-pin Cable Matching Pair - JST PH Compatible ($2.05) — 4‑pin JST‑PH style plug/socket pair, 20cm, 26AWG.
- Gravity 4-Pin PH2.0 to DuPont Male I2C/UART Cable Pack 30cm ($16.95) — pack of 10x cables: PH2.0 4‑pin to DuPont male, 30cm.
4‑wire jumper-style cables (board-to-board)
- Jumper Wire - 0.1, 4-pin, 4 ($3.25) — 4‑pin JST‑RE connectors, 4" length.
- Jumper Wire - 0.1, 4-pin, 12 ($5.55) — 4‑pin JST‑RE connectors, 12" length.
If you meant the “fully buckled” connector (not cable)
- JST SH 4-pin Vertical Connector (10-pack) ($8.35) — 1.0mm pitch 4‑pin connector (Qwiic/STEMMA QT style).
Electric Brick module mentioned in results
- OCTOPUS OLED Display ($26.10) — an OCTOPUS series electric brick module (useful if the search was actually targeting an Electric Brick part rather than just the cable).
Which 4-wire connector style do you need for the Electric Brick cable?
Showing 1-20 of 35 products
Servo - Generic High Torque Continuous Rotation (Standard Size)
Here, for all your mechatronic needs, is a simple, high quality continuous continuous rotation servo motor. This servo is able to take in 6 volts and deliver 66.7 oz-in. of maximum torque at 70 r/min. A standard 3-pin power and control cable is attached and all hardware listed below is included...
Servo - Generic, 180° Rotation (Sub-Micro Size)
·
Here is a simple, low-cost servo for all your mechatronic needs. This little guy is able to take in 6 volts and deliver 1.5kg/cm (at 6V). of maximum torque at 0.09 sec/60° (at 6V). This small servo comes with a standard 3 pin power and control cable, six arms and six screws. Note: This is the s...
Micro Servo 9g
This compact 9 g micro servo is an affordable, simple actuator for small mechatronics projects, robot linkages and model mechanisms. It can operate from 3.0 V to 7.2 V, with the supplied feature ratings listed at 6.0 V where noted.A 3-wire cable provides ground, power and control, terminated in a...
Servo - Hitec HS-422 (Standard Size)
This is the classic Hitec HS-422 servo. This solid consumer grade servo is able to take in 6 volts and deliver 57 oz-in. of maximum torque at 0.16 sec/60°, this is a simple servo for any beginner project!This high quality servo is perfect for your mechatronic needs and if you are looking to get i...
Hybrid Stepper Motor for 3D Printer (3.5kg)
A NEMA 17 hybrid stepper motor with 3.5 kg·cm holding torque, designed for 3D printers and CNC machines. This 2-phase motor has a 1.8° step angle and a 5 mm diameter drive shaft. Includes a 50 cm cable with an XH 2.54 connector, compatible with Ultimaker and similar control boards. Key Features ...
Servo - Generic Continuous Rotation (Micro Size)
Here, for all your mechatronic needs, is a simple, high quality continuous rotation servo motor. This servo is able to take in 6 volts and deliver 30.6 oz-in. of maximum torque at 0.14 sec/60° A standard 3-pin power and control cable is attached and all hardware listed below is included. Featu...
Servo - Generic High Torque (Standard Size)
A reliable, high-torque standard-size servo (FS5106B) with dual ball bearings and nylon gears. Delivering up to 83.47 oz-in of torque at 6V with a speed of 0.16 sec/60°, it's a versatile choice for robotics, RC, and mechatronics projects. Features a standard 3-pin power and control cable with 18...
Servo - Generic (Sub-Micro Size)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is very similar in size and specifications to the Hitec HS-55. This little guy is able to take in 6 volts and deliver 20.8 oz-in. of maximum torque at 0.10 sec/60° This small servo comes with a standard 3 ...
4-AAA Battery Holder
This battery holder accommodates 4× AAA batteries in series, providing approximately 6V from alkaline cells or 4.8V from NiMH rechargeables. It features wire leads for connecting to your electronics projects. Key Features 4× AAA Configuration – Series connection for 4.8–6V output Wire Leads –...
Bipolar Stepper Motor with Planet Gear Box (18kg.cm)
This bipolar stepper motor with planet gear box (gear ratio: 5.18) uses a standard 8mm-diameter D type output shaft, and has a 1.8° step angle (200 steps/revolution). Each phase draws 1.6 A at 2.78 V, allowing for a holding torque of 18kg-cm (176N-cm) (200rpm). The motor has a body dimension ...
Servo - Hitec HS-85MG (Micro Size)
The Hitec HS-85MG packs impressive torque into a micro-sized package. With metal gears and a single ball bearing, this servo delivers up to 3.4 kg·cm (48.6 oz·in) of torque at 6V while weighing just 21.9 g — making it an excellent choice for compact robotics, RC models, and mechatronic projects. ...
Alchitry Pt V2 Artix-7 FPGA Development Board
·
This is a platinum-tier FPGA development board designed for high-speed performance in compact builds. Its low-profile backside has no components taller than 1.5mm, enabling the use of high-speed 1.5mm stack-height DF40 connectors for GTP-capable interfaces such as PCIe 2.0.At the centre is a Xili...
9g micro servo (1.6kg)
A lightweight 9g micro servo with 1.6 kgf·cm of torque at 4.8V. Ideal for small-scale robotics, beam robots, and automation tasks where a compact, affordable servo is needed. At only 9 grams, it fits into tight spaces while providing reliable performance. Specifications Operating Voltage – 4.8...
Goteck micro metal gear servo (2.5kg)
This is a metal gear servo(2.5kg) from Goteck.It's very small, lightweight, and powerful! Metal gear for longer wear life and extra strength in demanding applications. Perfect for use in medium-sized electric airplanes,helicopters or mini Robots. SPECIFICATIONS Operating voltage...
9g Metal Gear Micro Servo (1.8Kg )
A compact 9g micro servo with metal gears, delivering 1.8 kgf·cm of torque at 4.8V. The metal gear train provides significantly better durability than plastic versions, especially in robotics applications where the servo is in near-constant motion. With a 180° operating angle and a 320:1 reducti...
Servo - Hitec HS-805BB (Giant Scale)
The Hitec HS-805BB is a giant-scale servo delivering up to 343 oz-in of torque at 6V, making it a powerhouse for large robotics builds, heavy-duty pan-tilt mechanisms, and oversized RC applications. Dual ball bearings and heavy-duty nylon gears ensure smooth, reliable operation under load. Comes...
Bionic Robot Hand (Right)
The bionic robot hand is made up of acrylic material. It consists of 5 micro metal servos, joints and one hand base. The special mechanical structure makes every finger can be controlled separately, all can move in certain range. And every finger has spring damping structure, it will protect the...
Bionic Robot Hand (Left)
The bionic robot hand is made up of acrylic material. It consists of 5 micro metal servos, joints and one hand base. The special mechanical structure makes every finger can be controlled separately, all can move in certain range. And every finger has spring damping structure, it will protect the...
Bulk 9 Gram Servo - 10 pack
A bulk pack of ten 9-gram micro servos — an affordable way to stock up for robotics, mechatronics, and RC projects. Each servo includes a ~25cm cable with a standard 3-pin female header, plus a full set of horn and screw accessories. These compact servos deliver 1.6 kg/cm of torque at 6.0V with ...
Micro 360 Degree Continuous Rotation Servo FS90R
These continuous rotation servos are ideal when you need very precise degrees of rotation, to build a dial display for example. Dimensions: 23.2×12.5×22 mm Weight: 9g Operating speed: 110RPM (4.8V) / 130RPM (6V) Stall torque : 1.3kg.cm/18.09oz.in (4.8V) / 1.5kg.cm/20.86oz.in (6V...
