All Products

SKU: DF-DFR1136 · MPN: DFR1136

This DFRobot motor driver carrier board is purpose-built for the UNIHIKER M10, featuring a tilted edge connector slot that positions the screen at an optimal viewing angle. It integrates a dual 3 A DC motor driver with separate motor power, plus onboard RGB LEDs and infrared transmitter/receiver....

SKU: MB-12040

This encoder motor is capable of driving two DC motors or one encoder motor. It has 16 pins, allowing you to connect with MegaPi by simply plugging in. The motor driver IC on the board is TB6612, which is a high efficiency MOSFET driver with low heat dissipation. Overcurrent protection included t...

SKU: KI-5698

A compact motor driver board for the BBC micro:bit that drives two DC motors or one stepper motor. The integrated edge connector lets the micro:bit slot in directly, with built-in protection against short circuits, overcurrent, and overheating. Power is supplied via terminal block or servo conne...

SKU: AF-3777

Perhaps you've been assembling a new robot friend, adding a computer for a brain and other fun personality touches. Now the time has come to let it leave the nest and fly on its own wings– err, wheels!  These durable (but affordable!) plastic gearbox motors (also known as 'TT' mot...

SKU: DF-FIT0493

A 12V DC gear motor with an integrated quadrature encoder, ideal for mobile robot platforms and closed-loop motor control. The 34:1 gearbox provides a no-load speed of 350 RPM with a stall torque of 12 kg·cm, and the encoder delivers 374 pulses per revolution of the output shaft for precise speed...

SKU: DF-DRI0001

The DFRobot 2×1A DC Motor Shield uses the L293 motor driver chip to control two 7–12 V DC motors at up to 1 A per channel. It stacks directly onto Arduino Uno and Arduino Mega boards, using pins 4, 5, 6, and 7 for motor control with PWM speed support. Key Features Dual Motor Drive – Control tw...

SKU: DF-DFR0429

INTRODUCTION An ordinary DC motor requires an H Bridge to work with a microcontroller such as an UNO. For newcomers to electronics, the process of finding the right motor driver, connecting it to the MCU and learning the relevant electronic theory can be confusing an...

SKU: DF-DFR0430

INTRODUCTION An ordinary DC motor requires an H Bridge to work with a microcontroller such as an UNO. For newcomers to electronics, the process of finding the right motor driver, connecting it to the MCU and learning the relevant electronic theory can be confusing and frustrating when you ju...

SKU: DF-FIT0489-D

This turbo worm gear motor delivers high torque through a durable metal gearbox with a 1:150 reduction ratio. The worm drive mechanism provides a self-locking output shaft that cannot be back-driven, making it ideal for applications where the load must hold position when the motor is off. Rated ...

SKU: DF-FIT0450

INTRODUCTION This is the DFRobot TT Micro DC geared motor with encoder. It is a motor with a 120:1 gearbox and an integrated quadrature encoder that provides a resolution of 16 pulse single per round giving a maximum output of 1920 within one round. With an Arduino cont...

SKU: DF-FIT0458

INTRODUCTION This is the DFRobot TT Micro DC geared motor with encoder. It is a motor with a 120:1 gearbox and an integrated quadrature encoder that provides a resolution of 16 pulse single per round giving a maximum output of 1920 within one round. With an Arduino controller and motor drive...

SKU: DF-DFR0411

INTRODUCTION This DC motor has an integrated transistor built in to the board, eliminating the need for a motor driver. Use PWM to control it for all your DIY project needs. It uses the 3 pin "gravity" interface saving lots of messy wiring. SPECIF...

SKU: DF-FIT0441

INTRODUCTION   This is a motor revolution: a new DC brushless motor with built-in motor driver. It can be conncected to Arduino directly without external motor driver. Whatsmore, the motor comes with directional control, PWM speed control and speed feedback output, which make this motor t...

SKU: AF-324

A stepper motor to satisfy all your robotics needs! This 4-wire bipolar stepper has 1.8° per step for smooth motion and a nice holding torque. The motor was specified to have a max current of 350mA so that it could be driven easily with an Adafruit motor shield for Arduino (or other motor driv...

SKU: PL-2267

A NEMA 17 hybrid bipolar stepper motor with a 1.8° step angle (200 steps per revolution). Each phase draws 1.7 A at 2.8 V, delivering a holding torque of 3.7 kg·cm. Four colour-coded wires with bare leads connect to two coils: black/green for one coil, red/blue for the other. Best driven with a ...

SKU: AF-3802

These durable (but affordable!) gearbox motors (also known as 'TT' motors) are an easy, low-cost way to get your projects moving. This is a TT DC All-Metal Gearbox Motor with a gear ratio of 1:90 about double of the 'standard' 1:48 ratio. That gives them higher torque but slower...

SKU: AF-3801

These durable (but affordable!) gearbox motors (also known as 'TT' motors) are an easy, low-cost way to get your projects moving. This is a TT DC Bi-Metal Gearbox Motor with a gear ratio of 1:90 about double of the 'standard' 1:48 ratio. That gives them higher torque but slower ...

SKU: AF-3882

What's this? A record player for ants?? Not at all! This is a DVD/CD Spindle Motor, that thing that's inside a CD or DVD player, that turns the disc around really fast. These motors have some great benefits that make them easier to use than '130' style DC hobby motors For one, they're mostly ...

SKU: AF-4416

This geared DC motor comes with a built-in magnetic encoder — a magnetic wheel and two Hall effect sensors are already attached to the motor body, giving you quadrature feedback for both speed and direction without any extra wiring or mounting. It's the ideal starting point for closed-loop motor ...

SKU: EC-ARS27361T

This motor shield uses dual TB6612 MOSFET drivers and a PCA9685PW I2C PWM controller to drive up to 4 DC motors or 2 stepper motors from an Arduino or compatible board. All motor control and speed management is handled via the I2C bus, freeing up digital pins for other uses. The stackable design...