All Products

SKU: AF-5648

The Adafruit STEMMA MOSFET Driver makes it safe and simple to control motors, solenoids, high-power LEDs, and other current-hungry loads from any microcontroller. Instead of wiring up a transistor and flyback diode on a breadboard, this compact board has everything built in — just connect power, ...

SKU: AF-355

When you need to switch a lot of power, N channel MOSFETs are best for the job. These FETs can switch over 60A and 30V and are TO-220 package so they fit nicely into any breadboard or perfboard. Heat sinking is easy with TO-220's, but because of the very low Rds(on) of down to 0.009 ohms (depe...

SKU: SF-DEV-10618

The SparkFun Power Driver Shield Kit lets you switch high-current loads directly from your Arduino using six RFP30N06LE N-channel MOSFETs. Connect a computer power supply or other DC source to drive motors, solenoids, LED strips, and other power-hungry devices with PWM control. Each of the six c...

SKU: SF-PRT-11214

MOSFETs are awesome. They’re like a switch that you flip electronically! This SparkFun MOSFET Power Controller makes it easy to switch a battery supply on and off using your favorite microcontroller. The board also has sewable pads so you can use it in e-textile projects that need more juice. Th...

SKU: SF-COM-23979 · MPN: COM-23979

Does your microcontroller need to control a high-voltage item, like a 12V LED strip, while also needing to be powered? Do you want to avoid having multiple power adapters and microcontrollers for your project? The MOSFET Power Switch and Buck Regulator (Low-Side) is one product we needed at Spark...

SKU: DF-FIT0261

INTRODUCTION Shape Memory metals that were developed by NASA for the space industry, and have been used for increasing applications down on earth.For example,there have been limited studies on using these materials in robotics. They make it possible to create very lig...

SKU: AF-5757

The Mosfetti by Monk Makes is a compact 4-channel MOSFET switch designed for maker projects. Each channel can drive up to 2 A of low-side switching at up to 16 V DC, making it perfect for controlling relays, solenoids, LED strips, pumps, and motors from a microcontroller. Supplied as a PCB with ...

SKU: DF-DFR1015

Multiple-output DC–DC converters are essential in a multitude of applications where different DC output voltages are required.This DC-DC step-down voltage power module converts 7.5V~30V input to an output of 3.3V/5V/9V/12V (default to 5V), which can be selected by short-circuiting the correspondi...

SKU: EC-ACS70028DH

The Dual Channel H-Bridge Motor Shield is composed of 2 discrete MOSFET H-bridge, designed to drive two DC motor with max current 8A. It is made up of 8 N-channel MOSFET IRF3205S and 4 pcs of half bridge motor controller IR2104, to build 2 H-bridge. With this shield and the Arduino board, users c...

SKU: DF-DFR0457

In most Arduino projects, relays are the first choice to drive some large current device. It requires a certain amount of current to drive the internal coil to pick-up contact. But for some MCU, like Intel Edison, Intel joule, lilypad, Raspberry Pi and other microcontroller with limited amoun...

SKU: PI-COM0202

A handy little pack of 5 operational amplifiers! Part no: LM224N LF347N Amplifier Type General Purpose J-FET Case or Package Type DIP14 DIP14 Gain Bandwidth Product 1.3 MHz 4 MHz Input Bias Current 20 nA 20 pA Input Offset Voltage 2000 uV 3000 uV Mounting Type Through Hole Through H...

SKU: AF-1438

The Adafruit Motor/Stepper/Servo Shield v2.3 is the upgraded successor to the original Motor Shield, delivering higher current, lower voltage drop, and a fully I2C-based design that frees up your Arduino's PWM pins. Drive up to 4 DC motors or 2 stepper motors plus 2 hobby servos from a single sta...

SKU: AF-1429

Control 24 channels of 12-bit PWM output with the Adafruit TLC5947 breakout board. Designed for LED control, this SPI-driven board delivers constant-current open-drain outputs that keep brightness consistent even if the power supply dips. The chainable design lets you connect as many boards as yo...

SKU: DF-FIT0827

The module adopts the standard Modbus RTU protocol, the communication interface supports RS485 or RS232 and supports communication baud rates of 2400, 4800, 9600, 19200, 38400 (default 9600). Each relay output is independent and can be connected to different load devices, such as 220V electric li...

SKU: SF-COM-24144 · MPN: COM-24144

This is a common MOSFET with very low on-resistance and a control voltage (aka gate voltage) that is compatible with any 3-5V microcontroller or mechanical switch. This allows you to control high-power devices with very low-power control mechanisms. Features: FET Type: N-Channel Technology: MO...

SKU: WS-26244

An RS485-controlled industrial I/O module with 8 isolated digital inputs and 8 open-drain digital outputs, communicating via the Modbus RTU protocol. Multiple protection layers — power isolation, magnetic isolation, TVS diode, and resettable fuse — ensure stable and reliable operation in demandin...

SKU: PI-COM0409

Simple SPDT slide switch. Rated at 30V/200mA. The pins have .1" spacing - fits great into a breadboard! Use it as a power switch or general control switch.Documents:Dimensional Drawing

SKU: AF-2439

An analog LED strip featuring both RGB and warm white (~3000K) LEDs at 60 LEDs per metre on a weatherproof white flexi PCB. Control the entire strip at once using any microcontroller and four transistors (one per channel) — no addressable LED library needed, just PWM for colour mixing. Power the...

SKU: MB-12040

This encoder motor is capable of driving two DC motors or one encoder motor. It has 16 pins, allowing you to connect with MegaPi by simply plugging in. The motor driver IC on the board is TB6612, which is a high efficiency MOSFET driver with low heat dissipation. Overcurrent protection included t...

SKU: SF-KIT-13682

If you do anything with electronics, you’re probably already using transistors, but you’re probably using them in large, prepackaged clusters of just one type. The SparkFun Discrete Semiconductor Kit addresses your needs of only needing one or a couple transistors without you needing go and order...