All Products

SKU: SF-PRT-28381 · MPN: PRT-28381

This is a single-row straight male header with 14 breakaway pins on standard 0.1 inch (2.54mm) spacing. It is suited to through-hole prototyping, module headers and breadboard-friendly maker projects.The 14x1 format is commonly used with Teensy 3.2 and Teensy 4.0 boards. If you are fitting header...

SKU: SF-PRT-13925

These headers are made to work with the Teensy 3.2 and Teensy LC development boards. Each kit of headers makes your Teensy breadboard compatible and will allow for stacking a Teensy and Teensy-compatible shield board. This kit includes five headers (two 13-pin, one 7-pin, one 3-pin, and one 2x...

SKU: SF-DEV-17119

The SparkFun Qwiic Shield for Teensy adds four Qwiic (I2C) connectors to your Teensy board, providing quick access to the SparkFun Qwiic ecosystem of sensors, actuators, and displays. Sized to fit the Teensy 4.0, Teensy 3.2, and Teensy LC footprints. The shield connects GND, 3.3V, SDA, and SCL f...

SKU: AF-3200

The Teensy 3.x Feather Adapter rearranges the pins of a Teensy 3.x board to match the Adafruit Feather form factor and pinout. This allows the Teensy to work with the full range of FeatherWing add-ons — motor drivers, GPS modules, LED matrices, OLEDs, and more. The adapter also includes a built-...

SKU: SF-PRT-29292 · MPN: PRT-29292

This is a compact 2x3 male through-hole header with 2mm pin spacing, suitable for soldering into compatible PCBs and add-on boards.The connector is unshrouded, uses square male pins, and is designed for simple push-pull mating. It is the same style of header included with the Ethernet Kit for Tee...

SKU: SF-PRT-28387 · MPN: PRT-28387

This header pin and socket set is intended for connecting the Ethernet pins on a Teensy 4.1 to a custom circuit board.The socket is designed to be soldered to the bottom side of the Teensy 4.1, making it useful when you need a neat board-to-board connection for a custom PCB design.Specifications:...

SKU: SF-PRT-13054

A 2×20 shrouded (boxed) header designed to match the Raspberry Pi GPIO pinout. It provides a keyed, polarised connection point so you can run a ribbon cable from your Pi's GPIO to a breakout board, HAT prototype, or custom PCB without the risk of plugging in backwards. The through-hole header ha...

SKU: SF-KIT-15716 · MPN: KIT-15716

This passive adapter lets a Teensy development board connect to the standard Arduino 1.0 (R3) shield footprint, making it easier to reuse existing Arduino shields without a breadboard full of jumper wires.Solder your Teensy board, sold separately, to the marked footprint on the adapter, then plug...

SKU: SF-PRT-17152

These headers are made to work with the Teensy 4.1, Teensy 3.6, and Teensy 3.5 development boards. Each set of headers allows for your Teensy to be easily incorporated into a breadboard circuit or attach a shield on top of the board. This kit includes three headers (two 24-pin, and one 5-pin), en...

SKU: SF-PRT-28372 · MPN: PRT-28372

Build large LED displays with a Teensy using this OctoWS2811 adapter board. It connects Teensy 3.2 through 4.1 boards to thousands of WS2811, WS2812 or NeoPixel-compatible LEDs, with support for driving up to eight strips in parallel via the high-speed OctoWS2811 Library.The adapter acts as an ac...

SKU: SF-DEV-17156

An extended Qwiic shield that adds four Qwiic connectors to Teensy 4.1, Teensy 3.6, and Teensy 3.5 boards. Connects the I²C bus (GND, 3.3 V, SDA, SCL) to two horizontal and two vertical Qwiic ports for easy daisy-chaining of I²C sensors and actuators. Includes a PROG button that mirrors the Teen...

SKU: SF-COM-28380 · MPN: COM-28380

Add a colour touchscreen to your Teensy project with this 3.2 inch TFT display. It provides 320x240 resolution for higher-resolution graphics and uses the ILI9341 display controller.The supplier recommends this display for use with Teensy 3.2 through to Teensy 4.1. It suits projects that need a c...

SKU: PL-1023

A 2×3-pin (6-pin) female header with standard 0.1" (2.54mm) spacing. This compact dual-row header is commonly used for ISP programming connections, small sensor breakouts, and custom cable assemblies. The 2×3 configuration matches the standard AVR ISP programming header pinout, making it essenti...

SKU: PI-COM0004

This extra-tall 2×20 female header is designed to connect custom PCBs and HATs to the Raspberry Pi GPIO pins. At 16.5 mm tall, it provides enough clearance for your board to sit above the Ethernet and USB jacks without interference. The header has 3 mm pin length on the underside, so there's no ...

SKU: AF-3883

These three Stacking Headers alone are, well, lonely. But pair them with our ItsyBitsy boards, and you're in business! Great for putting something a-top your ItsyBitsy, like this AirLift bitsy add-on. Also works great for 'short' Teensy boards - not Teensy 3.5 or 3.6 long s...

SKU: AF-3907

A colour-coded 2×20 pin header for the Raspberry Pi Zero and Zero W that makes it easy to identify pin functions at a glance. Each pin group is colour-coded so you can quickly find power, ground, and GPIO pins without counting or consulting a pinout diagram. Colour Coding Red – 5 V Yellow – 3...

SKU: LB-LS3938

This terminal block breakout module comes fully assembled and soldered, ready for use with Raspberry Pi boards.It is compatible with Raspberry Pi 1 Model B+, Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+, Pi 4 Model B, Pi Zero, and Pi Zero W.The module features 2.54 mm (0.1″) pitch terminal blocks su...

SKU: AF-1465

Stop searching for the AVR ISP pinout every time you program. This simple breakout adapter converts the standard 2×3 AVR ISP box header to two breadboard-friendly 1×3 rows, making it easy to wire up your programmer without crossed wires or guesswork. The adapter plugs neatly into any standard br...

SKU: AF-4871

A compact passive infrared (PIR) motion sensor that detects movement from people and animals at distances of 2 to 5 metres. Much smaller than standard PIR modules, this sensor is ideal for unobtrusive projects and plugs directly into a breadboard or perfboard. Powered from 3–12 V DC via an onboa...

SKU: AF-1902

The SmartLED Shield (V4) provides a simple, solder-free way to connect a Teensy 3.2, Teensy 3.5, or Teensy 3.6 to HUB75 RGB LED Matrix Panels. Just plug in your Teensy, connect your panel, and start displaying graphics, patterns, or animated GIFs using the SmartMatrix Library. The shield include...