All Products
Showing 41-60 of 100 products
SparkFun Ardumoto - Motor Driver Shield
The Ardumoto Shield is a dual-motor controller for Arduino based on the L298 H-bridge. It can drive two DC motors at up to 2A per channel, making it an excellent platform for RC vehicles and small autonomous robots. The board draws power from the Arduino's Vin line and includes blue and yellow L...
Gravity: I2C VEML7700 Ambient Light Sensor (0~120Klx)
The Gravity VEML7700 is a high-accuracy digital ambient light sensor that outputs readings directly in lux (lx) over an I²C interface. Built around the Vishay VEML7700 IC, it features a 16-bit ADC, a high-sensitivity photodiode, and a low-noise amplifier — delivering precise light measurements wi...
IIC TO GPIO shield V2.0
The DFRobot IIC to GPIO Shield V2.0 (DFR0013) expands your Arduino's digital I/O capacity by converting a single I2C bus into 16 additional digital I/O ports. Using just two data lines (SCL and SDA), the shield frees up your existing pins for other tasks — essential for robotics, interactive medi...
Prop Shield With Motion Sensors
The Prop Shield is meant for making interactive light and sound effects on small handheld props and wearable costumes. Motion Sensors - Allows motion interactive light & sound. Audio Amplifier - Clear quality audio output to a small speaker. Fast LED Driver - Drive APA102 / Dotstar LEDs fo...
STEM kit for Arduino
The STEM Kit for Arduino is a beginner-friendly electronics kit that provides everything you need to get started with Arduino prototyping. With the included sensors, displays, and components, you can build a wide range of projects — from reading environmental data to controlling LEDs and motors. ...
Arduino Leonardo
The Arduino Leonardo is a microcontroller board based on the ATmega32U4. Unlike previous Arduino boards, the ATmega32U4 has built-in USB communication, allowing the Leonardo to appear as a mouse and keyboard to a connected computer — in addition to a virtual serial/COM port. With 20 digital I/O ...
Pulse Sensor Amped
The Pulse Sensor Amped is a plug-and-play heart-rate sensor for Arduino. It detects pulse by measuring changes in reflected light as blood pumps through your tissues, providing a real-time analogue signal that fluctuates with each heartbeat. Compatible with both 3.3 V and 5 V Arduino boards, it ...
Octopus Non-invasive AC current sensor TA12-100 Brick
The Octopus TA12-100 is a non-invasive AC current sensor brick from ElecFreaks. It uses a current transformer to measure AC current flowing through a wire without needing to cut or splice the circuit — simply clamp it around the conductor. The sensor outputs an analogue voltage proportional to th...
Elecrow 37-in-1 Sensors Module Kit for Arduino
This 37-in-1 sensor kit provides a comprehensive collection of the most common and useful electronic modules for Arduino. Each module outputs signals directly when connected to an Arduino board, making it an ideal starter set for beginners learning about sensors, inputs, and outputs. Key Feature...
AVR ISP Shield V1.1
Did you know your Arduino can burn bootloaders onto Atmega chips, turning them into Arduino compatible microcontrollers? It required a breadboard and a whole mess of jumper wires but we've just made it a ton easier on you with the AVR ISP Shield!It is very easy to use. Just following the Arduino ...
8-Channel EL Shield
An Arduino-compatible shield for controlling up to 8 channels of EL (electroluminescent) wire or tape. Each channel uses opto-isolated, zero-crossing control for safe and reliable switching. Control EL wire as simply as turning an LED on and off, or use PWM for colourful animated effects. Compat...
Arduino Connector kit
A comprehensive collection of 24 types of commonly used Arduino connectors, all in one convenient kit. Includes male and female headers, USB connectors, switches, DC jacks, SD/TF card sockets, and more — everything you need for designing Arduino shields, custom controllers, and DIY electronics pr...
Arduino Uno Rev3
The board everybody gets started with, with the ATmega328 (SMD). It has 14 digital IO pins (6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, and more. The Arduino Uno SMD R3 is a microcontroller board based on the ATmeg...
Adafruit 3.4in Square RGB-666 TTL TFT Display with Touchscreen
·
This square TFT module is made for advanced display projects that need a high-resolution, compact screen. It has a 3.4 inch IPS panel with 480x480 full-colour pixels, giving a crisp square format with good colour visibility off-axis.The display uses an ST7701S driver with SPI for configuration an...
Red Vision Touch Display for RedBoard (Without Display)
·
This interface board is for Red Vision projects where you want the camera and vision stack, but would rather send video to a larger external monitor than use a small onboard screen. With the LCD removed, it acts as a streamlined bridge between a SparkFun Red Vision Camera Board and an RP2350 RedB...
Jumper Wires Premium 6 F/F Pack of 50
Premium female-to-female jumper wires, 155mm (6″) long, for connecting between male headers on development boards, breakout boards, and breadboards. The 0.1″ pitch connectors fit standard pin headers and can be installed side by side. Specifications Connector Type – Female to Female (F/F) Len...
8 x AA battery holder with 5.5mm/2.1mm Plug and On/Off Switch
·
This 8×AA battery holder provides a portable power source with a built-in on/off switch and a standard 5.5 mm / 2.1 mm DC barrel plug for easy connection to Arduino boards, LED strips, motors, and other 12V devices. Use alkaline AAs for approximately 12V at 3000–4000 mAh, or rechargeable NiMH cel...
12 VDC 1000mA regulated switching power adapter - UL listed
·
Warning: This is a US-plug adapter and is not certified for use in Australia. Only purchase if you are using it outside Australia or with an appropriate plug adapter. A regulated 12V DC switching power adapter delivering up to 1000mA (1A). The slim profile fits into power strips without blocki...
5 x AA Battery Holder with 2.1mm DC Jack
·
This 5×AA battery holder delivers approximately 7.5V from five AA batteries, terminated with a 2.1mm DC barrel plug (centre positive). It provides the ideal voltage for Arduino boards and other development boards with onboard 5V regulators, which typically need 1–2V of headroom above their output...
SparkFun FTDI Basic Breakout - 5V
This is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more compact. Functionality has remained the same. This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to wo...
