All Products

SKU: TB-HK7717

These knobs just push on to a standard 0.25 (1/4) shaft. - No more messy screws. - Complete with coloured cap. Specifications Colour / Finish Black Shaft Type 1/4" Flattened Side...

SKU: DF-FIT0628

Does it still bother you that you cannot access the Internet anytime anywhere? Here comes a new mini wireless network card, plug and play. Bring you a fast and stable wireless network!This is a 150M miniature USB WiFi module that fully complies with IEEE 802.11n standard, up to 150Mbs data rate a...

SKU: SF-PRT-28388 · MPN: PRT-28388

This ground loop isolator is a simple inline fix for unwanted hum and noise caused by ground loops in audio setups. Place it between your audio board and the line-in of an amplifier or other compatible audio equipment.The unit is bi-directional, so either side can be used as the input or output. ...

SKU: SS-101020044

Alcohol sensor is semiconductor sensor for alcohol detection. It has good sensitivity and fast response to alcohol, suitable for portable alcohol detector. Specifications Power requirements: 5 VDC @ ~120 mA (heater on) Detection Gas: Alcohol Concentration: 20-1000ppm Alcohol Inter...

SKU: SS-101020003

A simple momentary push button module in the Grove form factor. When pressed it outputs a HIGH signal; when released it returns to LOW. The button includes a built-in pull-down resistor, so it's ready to use as a digital input straight out of the box. Part of the Seeed Studio Grove ecosystem, it...

SKU: M5-A034-D

Description GROVE Cable would be a necessary tool used on M5Stack development, since all PORTs on M5Core are GROVE stadard. This Grove cable, compatible with the GROVE port on M5Core,simply have 4 lines, two for data, one for power,and one for Ground. We've offered alternative length: 10c...

SKU: M5-A034-C

Description GROVE Cable would be a necessary tool used on M5Stack development, since all PORTs on M5Core are GROVE stadard. This Grove cable, compatible with the GROVE port on M5Core,simply have 4 lines, two for data, one for power,and one for Ground. We've offered alternative length: 10c...

SKU: AF-5244

A 100 mm pigtail cable with a Seeed Grove connector on one end and four bare wires on the other, for connecting Grove-compatible boards and breakouts to custom wiring. Specifications Connector – Grove (2 mm pitch), 4-pin Length – 100 mm Wires – 4 (bare ends) Wire Colours Black – GND Red...

SKU: SS-110060762

Expand your micro:bit with the Grove Inventor Kit – a complete package of sensors, displays, and actuators that connect without soldering. The kit includes a Grove shield that adds plug-and-play Grove ports to your micro:bit, plus 8 carefully selected modules to get you building projects immediat...

SKU: SS-108020021

Features Easy to use Cartoon Style mini fan Soft fan-blade to avoid injuries Built-in programmable microcontroller that uses Arduino IDE You can change the code to drive servo motors instead of DC motor Description Hey hey, calm down, have some fresh air here. The Grove – Mini Fan v1.1 can be ...

SKU: AF-4309

The Grove Shield FeatherWing for Particle Mesh and all Feathers is an add-under for any Particle Mesh or Feather board, so that you can easily interface with Seeed's huge collection of Grove sensors. Now you can have full range of hundreds of Grove modules with Particle Mesh along with our Feathe...

SKU: SS-103030195

The Grove Shield for micro:bit is a plug-and-play expansion board that bridges the micro:bit with the Seeed Studio Grove ecosystem. It provides 4 Grove connectors on-board (covering different interfaces) with provision for 4 additional Grove ports, giving access to hundreds of Grove sensors, actu...

SKU: SS-101020023

The Sound sensor module is a simple microphone. Based on the power amplifier LM386 and the electret microphone, it can be used to detect the sound strength of the environment. The value of output can be adjusted by the potentiometer.   Features Grove compatible interface Wide supply vo...

SKU: SS-110060024

The Grove Starter Kit for Arduino from Seeed Studio is a beginner-friendly electronics kit built around the Grove modular connector system. It includes a Base Shield with multiple Grove connectors, twelve plug-and-play modules, and a user manual to help you get started quickly — no soldering or c...

SKU: SS-110061283

Raspberry Pi Pico swept the MCU world like a huge wave. Pico born with powerful performance, reasonable price, and comprehensive resources, it will definitely become a great platform for learning and mastering electronic knowledge.   To help you ride this wave, we launched the Grove Sta...

SKU: SS-110010044

The Grove Starter Kit for Seeed Studio XIAO bundles the XIAO Expansion Board with 9 Grove modules and additional components, providing a complete introduction to the XIAO development platform. Designed for beginners, it comes with free online courses to help you get started quickly. The kit cove...

SKU: M5-U039-B

Description Grove-T is a T-shaped hub. Is this remind you the HUB unit ? They are basically the same thing, just in different shape.This is also used for GROVE port expanding. Notice: Grove-T is just a hardware expander, if you are looking for hardware and software(standard prot...

SKU: EF-EF11096

Specially designed to connect to seeed studio sensors, seeed Sudio sensors can be used on sensor:bit, octopus:bit, Wukong or other expansion boards. Only ordinary seeed studio sensors can be connected, IIC devices can not be used.

SKU: M5-A046

1. Grove to GroveGROVE 2 GROVE is a GROVE extension connector. Two female GROVE port sit back-to-back.  One common use of this part is for the RGB LED strip extension. Feature:GROVE-to-GROVERGB LED strip extensionpackage includes: 5x connector2. Grove to PinGROVE 2 PIN is a GR...

SKU: AF-4528

A 100 mm adapter cable that bridges the gap between Grove and STEMMA QT / Qwiic ecosystems. One end features a Grove connector, the other a JST SH (STEMMA QT / Qwiic compatible) connector — making it easy to mix and match sensors, breakouts, and host boards across different connector standards. ...