All Products

SKU: SF-WIG-21277 · MPN: WIG-21277

Need more Qwiic ports without forcing every board into a single daisy chain? This star-shaped Qwiic MultiStar acts as a hub for the I2C bus, adding four extra usable Qwiic ports to a board that only has one.The board has five Qwiic connectors in total. One connects back to your main board, leavin...

SKU: SF-SEN-23220 · MPN: SEN-23220

Measure visible and near-infrared light with a compact Qwiic breakout based on the AS7343 multi-spectral sensor. It covers approximately 380nm to 1000nm and is suited to reflected, emitted and transmitted light measurements for spectroscopy tasks such as colour matching and spectral signature ana...

SKU: SF-GPS-30975 · MPN: GPS-30975

Built around the u-blox ZED-F9T-20B receiver, this breakout is made for projects where precise time matters as much as location. Under clear skies it can provide five nanoseconds of timing accuracy without requiring external GNSS correction data, making it suitable for 5G IoT networks, distribute...

SKU: SF-GPS-30018 · MPN: GPS-30018

Built around the u-blox SAM-M8Q module, this compact GNSS receiver is a straightforward way to add location tracking to a project. Plug in USB-C for power and configuration, or use the Qwiic connectors for solder-free I2C integration with compatible boards.The board includes an integrated smart a...

SKU: SF-GPS-28019 · MPN: GPS-28019

This high-precision positioning breakout is built around the Quectel LG580P GNSS module, giving projects centimetre-level RTK positioning plus instantaneous heading when used with two GNSS antennas. Unlike systems that need to move before they can infer direction, the dual-antenna setup can deter...

SKU: SF-SEN-29529 · MPN: SEN-29529

This ultra-small Qwiic-enabled breakout adds three-axis acceleration sensing to compact projects using the LIS3DH, a smart, low-power capacitive micro-machined accelerometer with 12-bit resolution. It can be used for translation detection and is classified as a 3DoF, or 3 Degrees of Freedom, sens...

SKU: SF-SEN-27544 · MPN: SEN-27544

When the ADC built into your microcontroller is not precise enough, this Qwiic breakout adds a high-resolution Texas Instruments ADS1219 for measuring very small analogue voltage changes.The board provides four channels of 24-bit analogue input, which can be used as four single-ended inputs or co...

SKU: SF-GPS-22693 · MPN: GPS-22693

This high-precision GNSS breakout is built around the u-blox ZED-F9R, combining RTK positioning with Automotive Dead Reckoning (ADR) sensor fusion. It fuses a 3D IMU sensor, wheel ticks, a vehicle dynamics model, correction data and GNSS measurements to provide accurate and continuous positioning...

SKU: SF-WRL-21327 · MPN: WRL-21327

This board is a low-power 2.4GHz BT beacon breakout built around the InPlay IN100 NanoBeacon. It is designed for fast deployment in wireless sensor monitoring, asset tracking, retail beaconing and real-time location tag projects where long field life and minimal programming are priorities.Power c...

SKU: SF-GPS-26620 · MPN: GPS-26620

Built around the Quectel LG290P, this compact RTK GNSS breakout is designed for high-precision positioning projects that need quad-band, multi-constellation reception. It follows the same board dimensions, pin layout and connectors as SparkFun’s GPS-RTK-SMA Breakout - ZED-F9P (Qwiic), making it a...

SKU: SF-GPS-23288 · MPN: GPS-23288

Bring high-precision GNSS positioning to your project with the u-blox NEO-F9P engine and dual-band L1/L5 reception. L5 signals sit in the protected ARNS band, helping reduce RF interference and improve reliability in challenging environments such as dense city streets.The breakout provides five s...

SKU: SF-COM-16917 · MPN: COM-16917

Show numbers, letters, characters and symbols in bright blue with this compact four-character alphanumeric display. Each digit uses fourteen segments, giving you far more flexibility than a standard seven-segment display.It connects through the SparkFun Qwiic system, so setup is simple: plug in a...

SKU: SF-COM-30416 · MPN: COM-30416

Control higher-power loads from a microcontroller over I2C with this Qwiic relay board. It is built around the Omron G6K-2F-Y DC3 dual-pole/dual-throw relay, letting a low-voltage logic system switch loads up to 1A at 30VDC or 0.3A at 125VAC at 40°C.The board offers both software and hardware con...

SKU: SF-LCD-29530 · MPN: LCD-29530

This compact OLED board gives your project a crisp monochrome white-on-black interface in a 1.5-inch square form factor. With 128x128 pixels and a 1:1 aspect ratio, it suits custom graphics, menus, status screens and data plotting.The display uses Chip-on-Glass (COG) OLED technology, so each pixe...

SKU: SF-SEN-24409 · MPN: SEN-24409

This compact breakout board measures moisture in soil and similar materials using two large exposed pads as conductivity probes. As the soil gets wetter, conductivity between the pads increases, resistance drops, and the sensor produces a higher analog SIG output.For quick setup, the board includ...

SKU: SF-PRT-26784 · MPN: PRT-26784

This compact Qwiic board lets you switch power to downstream Qwiic devices so high-current modules can be turned off when they are not needed. That can help conserve energy in battery-powered builds using GNSS and other power-hungry Qwiic boards.It also provides I2C bus isolation, so slower 100kH...

SKU: SF-COM-18565 · MPN: COM-18565

This compact white alphanumeric display gives you fourteen-segment characters for showing numbers, letters and symbols in your project. It uses the VK16K33 LED driver over I2C, so it is a neat fit for Qwiic-based builds where you want readable text without lots of wiring.With Qwiic, you can plug ...

SKU: SF-COM-16916 · MPN: COM-16916

Add letters, numbers and symbols to your project with red fourteen-segment digits that are much more flexible than a basic seven-segment display. This Qwiic display connects over I2C, so you can plug it in without soldering, without working out SDA and SCL by hand, and without adding separate vol...

SKU: SF-KIT-15209 · MPN: KIT-15209

This kit gives you the core hardware needed to start reading 125kHz RFID tags over I2C, without hunting for a separate reader module, antenna or wiring up a complex circuit. The box includes a SparkFun RFID Qwiic Reader, an ID-12LA RFID reader module, two 125kHz RFID cards and a 100mm Qwiic cable...

SKU: SF-GPS-28871 · MPN: GPS-28871

This GNSS RTK breakout brings the u-blox X20 engine to a maker-friendly board for high-precision positioning projects. It is designed around the ZED-X20P all-band receiver and can process signals from GPS, Galileo, BeiDou, QZSS and NavIC across all GNSS frequency bands, including L-band.The board...