All Products

SKU: AF-5940 · MPN: ADA5940

This breakout uses Vishay's TSSP77038 infrared demodulator to give you the raw demodulated output from a 38kHz IR signal, without the extra filtering used in typical remote-control receivers. That makes it a handy choice for reflective sensing, light barriers, fast proximity detection, and modula...

SKU: AF-5963 · MPN: ADA5963

The Adafruit 555 PWM Output STEMMA is a fully assembled 555 timer board that generates an adjustable square-wave PWM signal — no breadboard wiring or external components needed. An onboard trimmer pot lets you tune the frequency across two selectable ranges: approximately 1.5 KHz to 25 KHz, or 1....

SKU: AF-6404 · MPN: ADA6404

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitc...

SKU: AF-5888 · MPN: ADA5888

This handy STEMMA board lets you control 'true analog' LED strips and other PWM-able LEDs from a NeoPixel-compatible data line, without the usual extra wiring of separate driver FETs. A WS2811F handles the 800KHz NeoPixel signal and drives AO3406 N-channel FETs, so a common-anode RGB strip or LED...

SKU: AF-6406 · MPN: ADA6406

If you fancy connecting to anything else with a JST SH compatible 3-pin connector, this cable will do the trick. For example, our NeoPixel JST Breakout boards, or UPDI Friend, or Sparkle Motion, or other boards we have with JST SH connectors on them for simple digital/analog IO. It has a 1mm pitc...

SKU: AF-5967 · MPN: ADA5967

The Adafruit Proto Tripler PiCowbell gives your Raspberry Pi Pico or Pico W three side-by-side socket slots — plug in your Pico and up to two PiCowbell accessories with no soldering or stacking headers required. It also includes LiPo battery charging, a power switch, reset button, STEMMA QT conne...

SKU: AF-4045

This cable will let you turn a JST PH 3-pin cable socket into 4 individual tinned wires. These are great to match up with our JST 4-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded! Black for GND Red for V+ White for SDA Green for SCL Even though...

SKU: AF-5970 · MPN: ADA5970

The Adafruit TSMP96000 "Code Learning" Infrared IR Receiver Breakout detects IR signals across a wide frequency range of 20–60 KHz, making it perfect for "code learning" applications where you need your device to work with any IR remote control — even when you don't know the carrier frequency. U...

SKU: AF-4391

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the JST PH 3 pin. These are the horizontal style.You can use these with any of our JST PH 3 / STEMMA cables. They're not STEMMA QT compatible (those use the ...

SKU: AF-4401

This 4-wire cable is a little over 200mm / 7.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.This cable can be used with Qwiic or S...

SKU: AF-3814

For a really long time we assumed that the JST PH didn't have a free-hanging male header version. But then we found this JST-PH 2-pin Male Cable, and we were like, this is perfect! It's not a genuine JST connector, but it's 100% compatible with a nice clicky connection that you can ...

SKU: LB-LS3938

This terminal block breakout module comes fully assembled and soldered, ready for use with Raspberry Pi boards.It is compatible with Raspberry Pi 1 Model B+, Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+, Pi 4 Model B, Pi Zero, and Pi Zero W.The module features 2.54 mm (0.1″) pitch terminal blocks su...

SKU: AF-4663

The 6V Air Valve (FA0520E) is a 3-port solenoid valve for pneumatic systems, functioning similarly to an electrical relay. It features a common port (COM), a normally open port, and a normally closed port, allowing you to switch air flow direction by powering the valve on or off. The valve is ra...

SKU: AF-3950

This cable will let you turn a JST PH 4-pin cable port into 3 individual wires with high-quality 0.1" female sockets on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them such as the Hallowing or Trellis M4. Can also be used with any STEMMA bre...

SKU: AF-5971 · MPN: ADA5971

The Adafruit Chainable DS18B20 Extender Breakout makes it easy to connect multiple DS18B20 temperature sensors in a daisy chain using standard STEMMA JST PH 2mm cables. Each breakout includes screw terminal blocks for direct connection of DS18B20 sensors in TO-92 or waterproof cable form — no sol...

SKU: DF-SEN0487

This tiny MEMS microphone has an amplifier gain of 66. When there is no sound detected, it outputs voltage around 0.66*VCC. When speaking, you can easily get the acoustic waveform by ADC sampling. The module can be used on all kinds of 3.3V/5V main-controllers.Connection DiagramSpecificationSigna...

SKU: AF-4399

This 4-wire cable is 50mm / 1.9" long and fitted with JST SH female 4-pin connectors on both ends. Compared with the chunkier JST PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic or STEMMA ...

SKU: SF-PRT-17260

This is a 50mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together but can be used for other applications as well. The cable insulation is made from silicon making it more flexible than our original Qwiic cable particularly in t...

SKU: AF-3922

A 200 mm Molex PicoBlade 2-pin cable with 1.25 mm pitch connectors. The ultra-slim PicoBlade format takes up minimal PCB space while providing a secure friction-lock connection — ideal when standard 0.1" or JST PH connectors are too large. Specifications Connector Type – Molex PicoBlade Pitch...

SKU: SF-PRT-17257

This is a 500mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together but can be used for other applications as well. The cable insulation is made from silicon making it more flexible than our original Qwiic cable particularly in tig...