All Products

SKU: AF-4897

A 40-pin FPC to right-angle 2×20 IDC male plug header adapter board. Converts a standard 40-pin 0.5mm pitch FPC/FFC cable connection into a male GPIO plug, allowing you to connect HATs and Bonnets at a distance from your Raspberry Pi via a slim, flexible cable. Insert the male plug into your HAT...

SKU: AF-2223

Connect your own PCB to a Raspberry Pi B+ and stack on top with this normal-height female header with extra long pins.  The female header part is about 8.5mm tall, good for small HATs that do not to clear the USB/Ethernet jacks. This header has extra long 10mm pins, compared with our p...

SKU: PH-102895

A 150mm GPIO ribbon cable for Raspberry Pi with a 2×20 male connector on one end and a 2×20 female connector on the other. Extends the full 40-pin GPIO header for use with HATs, Bonnets, and other accessories at a distance from the board. Works with any 40-pin Raspberry Pi, including the Pi 400 ...

SKU: AF-2263

The Adafruit GPIO Reference Card makes it easy to identify and connect wires to the Raspberry Pi's GPIO header. This ultra-thin (0.8 mm) card slides directly onto the 2×20 GPIO header, labelling each pin by function — including I²C, UART, SPI, power, and general I/O — so you can wire up your proj...

SKU: LB-LR0387

This is the assembled version of the Pi T-Cobbler Plus.  It only works with the Raspberry Pi Model Zero, A+, B+, Pi 2, Pi 3 & Pi 4! (Any Pi with 2x20 connector)Each order comes with a 40 pin ribbon cable and assembled T-Cobbler Plus. You can plug the 40-pin GPIO cable between th...

SKU: AF-1658

Connect your own PCB to a Raspberry Pi with this extra-tall female header. The female header part has extra spaces to make it 13.6mm tall: when placed on your Pi, a PCB will clear the Ethernet and USB jacks. This header has 3mm of pins, compared with our stacking version which is the same base...

SKU: AF-4687

The Adafruit 2.13" Monochrome E-Ink Bonnet brings crisp, paper-like displays to your Raspberry Pi with no soldering required. Simply plug this pre-assembled bonnet onto any Pi with a 2×20 header and start displaying high-contrast black-and-white graphics that remain visible even with power discon...

SKU: SF-PRT-14275

This 2x20 male header has the same number and spacing of pins as a Raspberry Pi but is best served when used in conjunction with the Pi Zero since they come with a space of unpopulated headers. This through-hole header has 40 0.1"-spaced pins and can just be snapped into place with minimal sol...

SKU: AF-2187

A custom-made 2×20 short female header designed for surface-mount (SMT) Raspberry Pi HAT designs. This header provides the slimmest possible profile when you need a low-clearance connection between your HAT and a Raspberry Pi. While it requires SMT soldering skills (more challenging than standar...

SKU: AF-4114

The Zero2Go Omini is a multi-channel power supply board that sits on top of any Raspberry Pi with a 2×20 header. It accepts up to three separate power inputs and automatically selects the one with the highest voltage, making it perfect for projects that need backup power or flexible power source ...

SKU: AF-6358 · MPN: ADA6358

Build large, colourful HUB75 RGB LED matrix displays from a Raspberry Pi without the usual jumper-wire tangle. This Adafruit Bonnet plugs onto the 40-pin GPIO header and drives three parallel matrix strings using the active3 pinout, so it can handle roughly three times as many panels or pixels as...

SKU: AF-2711

With the Pi-EzConnect you can connect all sorts of electronics to a single Raspberry Pi  with no soldering or breadboarding! This HAT has screw-terminals for each pin on the Pi Header Key features: Solderless or soldered connections for all GPIO’s on a Raspberry Pi Mini proto area for...

SKU: AF-2262

The Adafruit GPIO Reference Card makes it easy to identify and connect wires to the Raspberry Pi's GPIO header. This ultra-thin (0.8 mm) card slides directly onto the 2×13 GPIO header, labelling each pin by function — including I²C, UART, SPI, power, and general I/O — so you can wire up your proj...

SKU: WS-19361

Quad GPIO Expander for Raspberry Pi Pico, Four Sets of Male Headers, USB Power Connector Quad GPIO Expander For Pico Four Sets Of Standard Raspberry Pi Pico GPIO Male Headers, USB-Powered Support Features At A Glance Standard Raspberry Pi Pico female header for direct attaching Raspberr...

SKU: WS-19343

A dual GPIO expander board for the Raspberry Pi Pico that duplicates all GPIO pins into two sets of 2×20 male headers. Plug your Pico into the centre female socket, then connect two expansion modules simultaneously — doubling your prototyping capability without rewiring. Features clear pinout la...

SKU: AF-1988

That new Raspberry Pi® Model B+ computer you just got has a row of 2x20 pin headers soldered on - those are the GPIO (general purpose input/output) pins and for those of us who like to hack electronics they are where the real fun is. By programming the Pi, you can twiddle those pins high or low, ...

SKU: AF-4855

A 2×2 (4-pin) female socket riser header with standard 2.54 mm (0.1 in) pitch, designed to fit the PoE header on the Raspberry Pi 3 B+ and 4. Use it alongside a 2×20 stacking header to raise the PoE HAT high enough to stack another HAT underneath. Specifications Configuration – 2×2 (4-pin) fem...

SKU: SF-SEN-16826 · MPN: SEN-16826

Bring 60GHz radar sensing into your project with the Acconeer A111 single-chip pulsed coherent radar sensor on a SparkFun breakout board. It is suited to high-precision distance measurement, and also supports gesture, motion, material and speed-detection applications at distances up to two metres...

SKU: AF-3578

Pimoroni's HyperPixel features a 4.0" display with 800x480 18-bit color pixels and a capacitive touch overlay, making it more sensitive and responsive than a resistive touch display. The plate uses the high speed DPI interface on the Pi and can use the mini display as a console, X window port, di...

SKU: SF-PRT-12790

This is a 2x23 pin female PTH header, with extra long legs which makes great for stacking. This piece is in the common configuration for Beaglebone Black headers. Each pin has a spacing of 0.1" in between each other. Documents: Datasheet