All Products

SKU: DF-FIT1036 · MPN: FIT1036

This compact 4015 BLDC motor combines a high-torque outer rotor motor with a factory-integrated AS5600 magnetic encoder, making it a neat motion-control package for robotics and precision motion projects.It is designed for Field-Oriented Control (FOC), also known as vector control, to support smo...

SKU: DF-FIT1034 · MPN: FIT1034

This compact three-phase brushless DC motor is built for advanced motion control projects where smooth torque, low noise and precise feedback matter. It runs at a rated 12V and combines a 2804 BLDC motor with a built-in AS5600 magnetic encoder for closed-loop control.The integrated encoder provid...

SKU: SF-COM-28236 · MPN: COM-28236

This add-on board solves a common Raspberry Pi Pico HAT problem: fixed orientation. It takes the standard pinout for a Raspberry Pi Pico development board and flips it as if the Pico had been physically rotated over, facing down.That makes it useful when your Pico needs to stay in a particular or...

SKU: DF-DFR1115-868 · MPN: DFR1115-868

This Gravity node module is a long-range, low-power wireless communication module for outdoor IoT sensor projects. It is based on the Semtech SX1262 RF chip, uses LoRa modulation, and operates on the EU868 frequency band for Europe and other regions that use this band.The module can work in LoRa ...

SKU: DF-DFR0789-W · MPN: DFR0789-W

This compact illuminated push-button module combines a tactile switch with a built-in white LED indicator, making it handy for interactive electronics, prototypes and embedded control panels.The switch outputs a digital HIGH/LOW signal and runs from +3.3-5V, so it suits common development boards ...

SKU: DF-FIT0916-MM · MPN: FIT0916-MM

This 5 pack of labelled 4-pin male-to-male DuPont cables is designed to make wiring Gravity modules, breadboards and development boards clearer during prototyping. Each 30 cm cable includes printed I2C and UART pin tags on the wires, helping you identify power, ground and signal lines without rel...

SKU: DF-TEL0177 · MPN: TEL0177

The Air780EU is a 4G Cat 1 communication module for IoT projects that need cellular connectivity across Europe, the Middle East, Russia, Thailand, Africa and other supported regions. It operates on LTE-FDD B1/B3/B7/B8/B20/B28 bands and provides up to 10Mbps downlink and 5Mbps uplink.It brings the...

SKU: SF-GPS-19390 · MPN: GPS-19390

This NEO-D9S breakout is an L-Band satellite correction data receiver designed to feed correction streams to a compatible multi-band, high-precision GNSS receiver such as the u-blox ZED-F9P. With a clear view of the sky, especially to the south, it can decode L-Band correction broadcasts and help...

SKU: SF-DEV-27878 · MPN: DEV-27878

The Io V2 is an Alchitry Element Board designed for learning and experimenting with digital design on Alchitry Au and Cu FPGA development boards. It keeps the same beginner-friendly controls and indicators as the original Io, now in the Alchitry V2 form factor.On-board interactive hardware includ...

SKU: DF-SEN0713 · MPN: SEN0713

This industrial-grade chlorophyll sensor measures chlorophyll concentration in water using the fluorescence principle, making it useful for algae monitoring in rivers, lakes, ponds, aquaculture systems and field research sites.The probe and housing are integrated into a single waterproof unit, wi...

SKU: DF-TEL0179 · MPN: TEL0179

Add LTE CAT1 connectivity to IoT projects and development boards with this Air780E communication module from DFRobot. It supports LTE-FDD B1/B3/B5/B8 and LTE-TDD B34/B38/B39/B40/B41 bands, making it suitable for deployments in China, India, Southeast Asia and other supported regions.The module pr...

SKU: AF-5635 · MPN: ADA5635

When an SD card is overkill, this small board gives your microcontroller project a handy chunk of non-volatile storage for files, images, fonts, audio clips and other data. It uses a W25Q16 flash chip, providing 16 Mbit / 2 MByte of external memory with lower cost and power usage than a full SD c...

SKU: LB-LS7860

A USB-C to Micro-USB cable for connecting Micro-USB development boards and devices to modern USB-C laptops and chargers. Ideal for programming boards like the micro:bit, Raspberry Pi Pico, Teensy 4.1, Circuit Playground Express, DFRobot Beetle, Maker UNO, and other Micro-USB devices.Specification...

SKU: SF-PRT-13925

These headers are made to work with the Teensy 3.2 and Teensy LC development boards. Each kit of headers makes your Teensy breadboard compatible and will allow for stacking a Teensy and Teensy-compatible shield board. This kit includes five headers (two 13-pin, one 7-pin, one 3-pin, and one 2x...

SKU: SF-PRT-08430

Premium female-to-female jumper wires, 155mm (6″) long, for connecting between male headers on development boards, breakout boards, and breadboards. The 0.1″ pitch connectors fit standard pin headers and can be installed side by side. Specifications Connector Type – Female to Female (F/F) Len...

SKU: SF-PRT-09385

A pack of 10 premium 12″ (30 cm) male-to-female jumper wires for breadboarding, prototyping, and connecting to 0.1″ pitch headers. Each wire has a male pin on one end and a female socket on the other, making them versatile for connecting between boards, sensors, and breadboards. The wires sit ne...

SKU: AF-1994

This 5V 2A USB power supply provides clean, regulated power for single-board computers like the Raspberry Pi and BeagleBone, or any other USB-powered device with high current demands. It outputs via a USB Type-A port, so you can use whatever USB cable your project requires. The supply outputs 5....

SKU: DF-FIT0063

A 10-pack of M3 × 10mm hexagonal standoffs with matching screws and nuts. Use them to mount circuit boards, sensors, and other components with consistent spacing and secure mechanical support. Standoffs are ideal for stacking boards in multi-level configurations, such as robot chassis builds or ...

SKU: AF-2857

The Adafruit Sensirion SHT31-D is a high-accuracy temperature and humidity sensor with a true I2C interface and PTFE filter for protection against dust and contaminants. Part of Sensirion's third-generation SHT sensor family, it delivers ±2% relative humidity and ±0.3 °C temperature accuracy for ...

SKU: AF-3456

This 5×AA battery holder delivers approximately 7.5V from five AA batteries, terminated with a 2.1mm DC barrel plug (centre positive). It provides the ideal voltage for Arduino boards and other development boards with onboard 5V regulators, which typically need 1–2V of headroom above their output...