All Products

SKU: DF-DFR0017

The DFRobot Relay Module is a standard relay used with a controller board to interface external electrical circuits or modules. Some of the most common applications with Arduino are: Home lighting, electrical appliances of high power and other equipments. The modular design makes it easy to in...

SKU: DF-DFR0979

The Gravity CH423 I2C 24 Digital IO Expansion Module extends your microcontroller with 24 additional digital output/input pins over a standard I2C connection. Based on the CH423 chip, it provides 8 GPIOs with interrupt support and 16 dedicated GPOs. The built-in current drive circuit delivers up...

SKU: DF-DFR0643

The traditional relay module has complicated wiring and is not friendly to beginners or students. The simple switch module simplifies the wiring method for connecting traditional relays. The input end is equipped with an adapter, which can be compatible with most power sources, battery boxes, DC ...

SKU: DF-DFR0473

Introducing the Gravity Digital Relay Module - the latest addition to DFRobot's Gravity series! This module is a little different to the other relays in our store - not only is it compatible with 5V Arduino boards, but also with Raspberry Pi, BBB (BeagleBoard Black), mbed, Intel Joule, Arduino 10...

SKU: DF-SEN0239

A digital infrared proximity sensor with adjustable detection range from 0 to 200 cm. Outputs a simple digital signal — HIGH when an obstacle is detected, LOW when clear. The detection threshold is adjustable via a rear-mounted screw, making it easy to tune for different applications. Features t...

SKU: LB-LR0046

The 5V 1-Channel Optocoupler Relay Module provides safe, isolated switching of high-voltage loads from a microcontroller. An onboard SMD optocoupler isolates the control circuit from the relay, protecting your Arduino, Raspberry Pi, or other development board from voltage spikes. A jumper settin...

SKU: DF-DRI0056 · MPN: DRI0056

This Gravity haptic driver module is built for Linear Resonant Actuators (LRAs), turning simple I2C commands into crisp tactile feedback for interactive projects. It is powered by the TM6605 driver chip and supports LRA resonant frequencies from 140Hz to 220Hz.The module includes 44 built-in vibr...

SKU: DF-KIT0018

The DFRobot Gravity Intermediate Kit for Arduino takes you beyond the basics with a comprehensive set of sensors, modules, and an Arduino-compatible board. Starting with simple LED projects and progressing to more complex builds like a mini electronic drum kit, sound-activated LED, and digital di...

SKU: DF-DFR1036 · MPN: DFR1036

A 1-channel DAC module that converts a PWM signal from any microcontroller into a precise 0–5V or 0–10V analogue voltage output. Built around the GP8101S chip with 8-bit resolution and 0.2% accuracy, it's ideal for driving standard 0–10V or 0–5V controlled devices in automation projects — lights,...

SKU: DF-DFR1184 · MPN: DFR1184

The Gravity 0–10V ADC Module is a high-precision dual-channel analogue-to-digital converter designed to interface industrial-grade 0–10V sensors with microcontrollers and Linux-based systems. Built on the Texas Instruments ADS1115, it delivers 15-bit resolution (0.375 mV per step) with ±2 mV accu...

SKU: LB-LR0051

A 4-channel relay module with opto-isolated inputs for safe, reliable switching of high-power loads. Each relay is rated for up to 10A at 250VAC or 30VDC, making it suitable for controlling lights, motors, heaters, and other mains-powered devices from a microcontroller. The opto-isolators protec...

SKU: DF-SEN0678 · MPN: SEN0678

This Gravity air quality module uses Sensirion’s STCC4 gas sensing chip to directly measure carbon dioxide with the thermal conductivity measurement principle. It is designed for compact, cost-effective indoor monitoring nodes where stable CO₂ readings are needed without complex hardware integrat...

SKU: LB-LR0002

The 5V 1-Channel Relay Board Module provides a simple way to switch high-voltage loads from your Arduino, Raspberry Pi, or other microcontroller project. Controlled via a 5–12V TTL signal, this relay can switch loads up to 250V AC, making it suitable for controlling lights, fans, pumps, and other...

SKU: DF-DFR0029-B

The Gravity Digital Push Button (Blue) is a simple momentary push button module designed for the DFRobot Gravity interface. It features an onboard LED indicator, immersion gold PCB surface, and a coloured button cap. A "D" marking on the board identifies it as a digital sensor for quick wiring re...

SKU: WS-26517

The Industrial Modbus RTU 8-Channel Relay Module (D) is a reliable RS485-controlled relay module with 8 digital inputs. Designed for industrial applications, it supports the Modbus RTU protocol and includes multiple isolation protections like power, magnetic, and TVS diode isolation. It features ...

SKU: DF-TEM2022B-EN-1

An all-in-one IoT starter kit built around the FireBeetle 2 ESP32-E, designed by Hackster and DFRobot for learning IoT development with Arduino. The kit includes sensors, actuators, an audio player with speaker, and an I/O shield — everything needed to build connected projects right out of the bo...

SKU: DF-DFR0457

In most Arduino projects, relays are the first choice to drive some large current device. It requires a certain amount of current to drive the internal coil to pick-up contact. But for some MCU, like Intel Edison, Intel joule, lilypad, Raspberry Pi and other microcontroller with limited amoun...

SKU: DF-SEN0463

This Gravity Geiger Counter Module detects ionising radiation — including nuclear radiation, X-rays, and cosmic rays — using a large M4011 Geiger-Müller tube. When ionising particles pass through the tube, the module outputs a digital pulse that can be counted by any microcontroller to calculate ...

SKU: SF-COM-00100

These are high quality Single Pole - Double Throw (SPDT) sealed relays. Use them to switch high voltage, and/or high current devices. This relay’s coil is rated up to 12V, with a minimum switching voltage of 5V. The contacts are rated up to 5A (@250VAC, 30VDC).

SKU: DF-DFR0144

This 4-channel relay shield from DFRobot plugs directly onto an Arduino Uno or compatible board, providing opto-isolated relay switching for controlling high-power devices such as lamps, water pumps, and motors. Each relay has its own test button and LED status indicator. The shield features a b...