All Products

SKU: AF-6353 · MPN: ADA6353

The Adafruit STSPIN220 Stepper Motor Driver Breakout makes controlling bipolar stepper motors simple with a GPIO-only interface — just two pins (DIR and STEP) are all you need. It defaults to 1/16 microstepping and supports up to 1/256 microstepping via mode pin configuration, making it ideal for...

SKU: AF-6109 · MPN: ADA6109

The Adafruit A4988 Stepper Motor Driver Breakout simplifies stepper motor control down to just two pins — a direction pin and a step pin. Each pulse on the step pin advances the motor by one step or microstep, making it straightforward to achieve precise, controlled motion without complex timer o...

SKU: AF-6121 · MPN: ADA6121

The Adafruit TMC2209 Stepper Motor Driver Breakout Board makes controlling stepper motors easy and virtually silent. Using Trinamic's "Stealth Chopper" technology, this driver delivers smooth, quiet microstepping with just two control pins — no timers, PWM, or real-time microcontroller required. ...

SKU: AF-2448 · MPN: 2448

The Adafruit TB6612 Breakout is a compact dual H-bridge motor driver that can spin two DC motors bidirectionally, step one bipolar or unipolar stepper, or fire two solenoids — all at up to 1.2A continuous per channel (3A peak). It's the same driver chip used in the Adafruit Motor Shield and Motor...

SKU: SF-ROB-14451

The SparkFun TB6612FNG Motor Driver breakout can independently control up to two DC motors at a constant current of 1.2 A (3.2 A peak). Each motor channel supports four modes — clockwise, counter-clockwise, short-brake, and stop — controlled via two input signals and a PWM speed input. All pins ...

SKU: AF-3416 · MPN: 3416

The Adafruit 16-Channel PWM/Servo Bonnet adds precision servo and PWM control to your Raspberry Pi. Using the PCA9685 I2C PWM controller, it drives up to 16 servos or PWM outputs simultaneously with 12-bit resolution — completely free-running with no Pi processing overhead. Up to 62 bonnets can ...

SKU: AF-815 · MPN: 815

The Adafruit 16-Channel PWM/Servo Driver uses the PCA9685 chip to provide 16 channels of 12-bit PWM output over I2C. With a built-in clock, the driver runs independently — no need to continuously send signals from your microcontroller. Ideal for controlling servos, LEDs, or any PWM-driven device....

SKU: AF-3190 · MPN: 3190

The Adafruit DRV8871 is a single-channel brushed DC motor driver breakout capable of delivering up to 3.6 A peak current with a wide 6.5–45V motor voltage range. Its resistor-set current limiting and built-in PWM support make it straightforward to use with virtually any brushed DC motor. The boa...

SKU: DF-DRI0050

This is a PWM driver board with four adjustment methods, namely, Python code direct control, PC host computer control, UART communication programming control, and potentiometer manual control. It is used in application scenarios such as DC motor speed control and light adjustment. This produ...

SKU: KS-KS4033

The micro:bit DRV8833 Motor Driver Expansion Board adds dual DC motor control to the BBC micro:bit. Built around the DRV8833CPWP motor driver IC, it can output up to 700 mA per channel with four control modes: clockwise rotation, anticlockwise rotation, brake, and stop. The board includes on-boa...

SKU: PL-1182

A breakout board for the Allegro A4988 DMOS microstepping stepper motor driver with translator and overcurrent protection. It lets you control one bipolar stepper motor at up to 2 A per coil (with sufficient cooling) using a simple step-and-direction interface. The board ships with all surface-m...

SKU: SF-ROB-21867

The SparkFun 3-Phase Brushless Motor Driver, featuring the TMC6300 from ADI + Trinamic, is a powerful and easy-to-use three-phase motor driver that was designed to control our Brushless Gimbal Motor. It can be used to control any 3-phase BLDC or PMSM motor with up to 2A (1.4ARMS) of total driv...

SKU: AF-3297 · MPN: 3297

The Adafruit DRV8833 is a dual H-bridge motor driver breakout, capable of driving two DC motors bidirectionally or one bipolar/unipolar stepper motor at up to 1.2 A per channel. It's well suited for low-voltage applications, operating from 2.7V to 10.8V motor power. The DRV8833 features built-in...

SKU: EC-ARS27361T

This motor shield uses dual TB6612 MOSFET drivers and a PCA9685PW I2C PWM controller to drive up to 4 DC motors or 2 stepper motors from an Arduino or compatible board. All motor control and speed management is handled via the I2C bus, freeing up digital pins for other uses. The stackable design...

SKU: PL-2515

The Pololu Dual G2 High-Power Motor Driver 18v18 Shield uses pairs of discrete MOSFET H-bridges to drive two large brushed DC motors. It has an Arduino shield form factor for direct plug-in use, and also breaks out all motor driver pins along the left side for standalone operation without an Ardu...

SKU: LB-LR0149

The EasyDriver is a simple stepper motor driver board based on the Allegro A3967 IC. It accepts a digital step/direction input (3.3 V or 5 V logic) and drives bi-polar stepper motors (4, 6, or 8 wire) at any voltage within the 7–30 V supply range. The board features adjustable current control fr...

SKU: DF-DRI0042

The DFRobot DRI0042 is a compact, high-current DC motor driver capable of continuously driving a single motor at up to 15A (with heatsink) from a 12–36V supply. The onboard LM2575 regulator provides a 5V 500mA output for powering an Arduino or other controller, and all control signal inputs inclu...

SKU: DF-DRI0001

The DFRobot 2×1A DC Motor Shield uses the L293 motor driver chip to control two 7–12 V DC motors at up to 1 A per channel. It stacks directly onto Arduino Uno and Arduino Mega boards, using pins 4, 5, 6, and 7 for motor control with PWM speed support. Key Features Dual Motor Drive – Control tw...

SKU: PL-4035

This compact breakout board for TI’s DRV8874 motor driver offers a wide operating voltage range of 4.5 V to 37  and can deliver a continuous 2.1 A (6 A peak) to a single bidirectional brushed DC motor. The DRV8874 also features integrated current sensing and regulation as well as built-in pr...

SKU: DF-DFR0399

A compact DC micro metal gear motor with a built-in driver that uses the DFRobot Gravity 3-pin interface. Simply connect to a microcontroller and control direction and speed with a single PWM signal — no external H-bridge required. The embedded driver accepts standard servo-style PPM signals, so...