All Products

SKU: PI-1SHEELD

The 1Sheeld+ is a Bluetooth shield for Arduino that turns your smartphone into over 40 different Arduino shields. Connect your iPhone or Android device via the free 1Sheeld app, and use your phone's sensors, camera, GPS, social media, and more directly from your Arduino sketch. The shield acts a...

SKU: AF-1438

The Adafruit Motor/Stepper/Servo Shield v2.3 is the upgraded successor to the original Motor Shield, delivering higher current, lower voltage drop, and a fully I2C-based design that frees up your Arduino's PWM pins. Drive up to 4 DC motors or 2 stepper motors plus 2 hobby servos from a single sta...

SKU: PL-5030

The Motoron M3S256 Triple Motor Controller Shield for Arduino makes it easy to control DC motors from an Arduino or Arduino-compatible board through an I²C interface. Each module can independently control up to three motors, and multiple shields can be stacked on top of the same Arduino for proje...

SKU: DF-DFR0327

The Gravity Arduino Shield for Raspberry Pi brings Arduino-compatible I/O to your Raspberry Pi B+, 2B, 3B, 3B+, or 4B. Built around the ATmega32u4 (Arduino Leonardo), it sits on top of your Pi and gives you access to all standard Arduino shields and sensors alongside the Pi's own GPIO, I2C, SPI, ...

SKU: DF-DFR0256

The Mega Multi IO Expansion Shield lets you stack up to four shields simultaneously on an Arduino Mega or Due without worrying about I/O pin conflicts. All Mega I/O pins are expanded and routed to four separate shield slots, keeping your project clean and tidy with organised cabling. Key Feature...

SKU: SF-DEV-18426

The MyoWare® 2.0 Arduino Shield is designed to easily connect up to six MyoWare 2.0 Muscle Sensors and Link Shields using 3.5mm TRS-to-TRS audio cables. The board comes pre-populated with male headers so all you would need to do is stack it on your Arduino and connect the sensors to read up to si...

SKU: PI-TSX00004

Add a SD slot and prototyping area in a single shield The Arduino MKR SD Proto Shield allows you to easily connect an SD card to your MKR form factor board. Use it to enhance the IoT features of your MKR1000, as well as store data coming from the web or sensors read by your board! There's al...

SKU: TB-XC4472

This versatile motor and servo controller shield for Arduino drives up to 4 bidirectional DC motors or 2 stepper motors, plus 2 servos — all from a single board. The 4 onboard H-bridges provide 0.6A per channel (1.2A peak) with thermal protection, and the dedicated servo ports use the Arduino's h...

SKU: DF-DFR0274

The RGB LED Strip Driver Shield allows you to control 12 V RGB LED strips (common anode) directly from an Arduino. With three PWM outputs capable of up to 3 A each, the shield can drive up to 10 metres of RGB LED strip. A built-in IR receiver enables remote control operation, and an on-board fuse...

SKU: DF-DFR0272

An Arduino-compatible Ethernet shield based on the Wiznet W5200 chip, providing a simple way to connect your Arduino to a network. It plugs directly onto an Arduino Uno or Mega 2560 and supports stacking additional shields on top. An aluminium alloy heatsink is fitted to the W5200 chip for therma...

SKU: PI-TSX00001

The prototyping shield designed for your MKR board! The MKR Proto Shield is a prototyping shield designed for your Arduino MKR board. This shield easily plugs onto your MKR using its provided female/male headers, and offers a duplicate breakout for each pin on the board along with many ...

SKU: AF-85

“How could something so simple be so useful?”  We heard once that in the 4th millenium B.C. some guy asked the person who invented the wheel that question.  The person who invented the wheel’s answer, we were told, was something like “well it’s not actually that simple - i...

SKU: DF-DFR0308

The Arduino DTMF Shield is a dual-tone multi-frequency decoder module that lets your Arduino interpret touch-tone signals from phones. Connect it to a GSM/GPRS shield and you can send commands to your Arduino via phone call — press buttons on your phone to control motors, lights, or any connected...

SKU: SF-DEV-11287

The Arduino WiFi Shield allows an Arduino board to connect to the internet using the 802.11 wireless specification (WiFi). It is based on the HDG204 Wireless LAN 802.11b/g System in-Package. An Atmega 32UC3 provides a network (IP) stack capable of both TCP and UDP. Use the WiFI library to write s...

SKU: PI-A000080

The Arduino Mega Proto Shield Rev3 is a prototyping board designed for the Arduino Mega 2560 standard pinout. It provides a dedicated area for soldering through-hole and surface-mount components, making it easy to build custom circuits as a single stackable module. The shield features extra conn...

SKU: DF-DFR0224

The Arduino Screwless Terminal Shield breaks out all Arduino Uno-compatible header pins to spring-loaded push-in terminal blocks. Press the lever, insert your wire, and release — no screwdriver needed. The shield stacks with standard Arduino shields, so you can add additional boards on top. Key ...

SKU: DF-DRI0009

The DFRobot 2×2A DC Motor Shield uses the L298P dual full-bridge driver chip to control two DC motors at up to 2 A per channel. It stacks directly onto Arduino Uno and Arduino Mega boards, using PWM pins 5 and 6 for speed control and digital pins 4 and 7 for enable/disable. The shield can be pow...

SKU: DF-DFR1107 · MPN: DFR1107

The Arduino GIGA Display Shield is a touchscreen add-on designed for the Arduino GIGA R1 WiFi. Featuring a 3.97" TFT display with 480×800 resolution and 5-point capacitive touch, it makes it easy to deploy graphic interfaces for dashboards, handheld devices, and interactive projects. Beyond the ...

SKU: DF-DFR0262-AC

The Arduino GSM Shield allows an Arduino board to connect to the internet, make and receive voice calls, and send and receive SMS messages. It uses the Quectel M10 radio modem and can be controlled via AT commands or the built-in Arduino GSM library. The shield communicates with the Arduino via ...

SKU: SF-KIT-15716 · MPN: KIT-15716

This passive adapter lets a Teensy development board connect to the standard Arduino 1.0 (R3) shield footprint, making it easier to reuse existing Arduino shields without a breadboard full of jumper wires.Solder your Teensy board, sold separately, to the marked footprint on the adapter, then plug...