All Products

SKU: AF-276

This FCC/CE certified and UL-listed switching power supply delivers a clean, regulated 5V DC output at up to 2A (2,000mA) via a standard 5.5×2.1mm DC barrel jack. It accepts 110–240V AC input and is suitable for powering LED strips, motors, and other current-hungry 5V devices. Key Features Out...

SKU: AF-1917

The Sensor Film Kit is a great new way to make custom-sized sensors out of force sensitive material. This kit includes one piece of black plastic sensor film (it's thicker and more durable than Velostat but similar in function), two pieces of heavy aluminum foil, and two pieces of clear adh...

SKU: AF-519

Measuring stretch forces isn't easy - unless you have some conductive rubber cord! This cord is 2mm diameter, and 1 meter long, made of carbon-black impregnated rubber. Usually this material is used for EMF gasketing, but its also very fun to play with.In a 'relaxed' state, the resistance is abou...

SKU: AF-291

 The classic 'third hand tool,' as seen on every desk! We have one next to our Panavise jr, they complement each other well. This tool is good for holding small PCBs and wires for tinning or soldering to parts.  Every part can rotate around in any way with thunbscrews and wingnuts....

SKU: AF-166

The Interlink 402 is a round force-sensitive resistor (FSR) with a 12.7 mm (0.5″) sensing area. It changes resistance based on applied pressure — the harder you press, the lower the resistance — making it a simple, low-cost way to detect physical pressure, squeezing, and weight in your projects. ...

SKU: SF-CAB-11579

Behold, the Hydra! This USB power cable probably looks a lot like something you’ve hacked together before. We do it all the time, because what is a computer if not a 5V power supply that happens to run software? The Hydra brings the 5V and GND lines from your USB power supply, computer or oth...

SKU: SF-TOL-11784

Are you frustrated with the lack of dexterity from most third hands? The SparkFun Third Hand gives you the ability to hold a board between two alligator clips on two flexible arms with multiple points of articulation. The arm’s wide range of articulation gives you access to any angle of the bo...

SKU: SF-TOL-12033

A parts kit for building or repairing an additional arm on the SparkFun Third Hand soldering helper. Includes alligator clips and the hardware needed to convert a coolant hose segment into a flexible helping hand. Ideal For Adding extra arms to the SparkFun Third Hand Replacing broken or worn c...

SKU: SF-TOL-09317

This is a solderer’s best helper, the third hand. Comes with a heavy base, two alligator clips, a soldering iron holder, and a good magnifying glass. Note that we don’t normally need a third hand. It’s nice, but soldering flat on a table works just fine. Then again, the desk is starting to loo...

SKU: AF-1222

The Adafruit GEMMA V2 is a tiny, coin-sized wearable microcontroller board powered by an ATtiny85 processor. At just 28 mm in diameter, it's small enough to fit into any sewable or wearable project, and affordable enough to dedicate to every build. Program it over USB with the Arduino IDE and bri...

SKU: AF-2024

The Adafruit Capacitive Touch Shield brings 12 channels of capacitive touch sensing to any Arduino using the MPR121 chip. Each sensor has a "figure 8" pad with holes designed for quick alligator clip connections — attach one end to the shield and the other to any conductive object like metal, fru...

SKU: AF-2340

The Adafruit Capacitive Touch HAT adds 12 capacitive touch sensors to your Raspberry Pi using the MPR121 touch controller over I2C. Each sensor has a figure-8 hole designed for alligator clip connections — attach clips to the HAT and the other end to anything conductive (metal, fruit, vegetables,...

SKU: AF-1849

Get started with wearable electronics using the Adafruit Gemma Sensor Starter Pack. This all-in-one kit includes a GEMMA V2 board, sewable RGB NeoPixels, multiple sensors, a rechargeable battery with charger, and everything you need to build interactive sewable projects — no soldering required. ...

SKU: AF-1657

Get started with Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic project. There's a GEMMA board, four sewable bright RGB pixels, a battery holder and batteries, 2-ply conductive thread, alligator clips to help you test out your circuit, and a U...

SKU: AF-3670

High-conductive heating fabrics are Literally! This non-woven fabric feels a little like felted paper but is filled with conductive material that can make the fabric emit heat when powered. Resistive heating fabrics safely deliver comfortable conductive and radiant heating at low voltage thr...

SKU: LB-00240

FunKey is a new product series from Architectronics that extends the functionality of another familiar touch board and is better designed, more affordable and simpler to use. FunKey Simple: 18 keystrokes easily reconfigured to any keystrokes using simple app all alligator, no "headers" touch...

SKU: AF-1466

This UL-listed switching power supply delivers a clean, regulated 5V DC output at up to 4A (4,000mA / 20W) via a standard 5.5×2.1mm centre-positive DC barrel jack. It accepts 110–240V AC input and is ideal for powering LED matrices, NeoPixel strips, and other high-current 5V projects. Key Featur...

SKU: AF-3915

Keep your Circuit Playground Express safe in this snap-together acrylic enclosure. Designed by Ada-friend Mike Doell, this minimal but elegant case turns your board into an electronic snowflake shape with no tools required for assembly. The enclosure provides full access to all buttons, the slid...

SKU: LB-LS0823

The Micro: bit GPIO T-type Expansion Board is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pin. This breakout board for the micro:bit’s edge connector allows intermediate and advanced users to connect the micro:...

SKU: MM-SKU00063

With this kit, you get everything you need to start learning about connecting electronics to your micro:bit in an accessible and easy manner. Everything is connected using the supplied alligator clips, so no soldering required. This kit suitable for children as young as 10 with some adult help...