All Products

SKU: AF-4855

A 2×2 (4-pin) female socket riser header with standard 2.54 mm (0.1 in) pitch, designed to fit the PoE header on the Raspberry Pi 3 B+ and 4. Use it alongside a 2×20 stacking header to raise the PoE HAT high enough to stack another HAT underneath. Specifications Configuration – 2×2 (4-pin) fem...

SKU: PI-COM1105

Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and bazinga! Your header is securely attached to your Pi Zero or pHAT. If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers might be just t...

SKU: AF-3413

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need. They come in both male and female, and use crafty little retaining nubbins to grip tightly into the holes on the PCB. Ab...

SKU: AF-2222

Connect your own PCB to a Raspberry Pi B+ with this normal-height female header.  The female header part is about 8.5mm tall, good for small HATs that do not to clear the USB/Ethernet jacks. This header has 3mm of pins, compared with our stacking version which is the same base height but ...

SKU: PI-COM0004

This extra-tall 2×20 female header is designed to connect custom PCBs and HATs to the Raspberry Pi GPIO pins. At 16.5 mm tall, it provides enough clearance for your board to sit above the Ethernet and USB jacks without interference. The header has 3 mm pin length on the underside, so there's no ...

SKU: AF-1992

Connect your own PCB to a Raspberry Pi B+ with this extra-tall female header. The female header part has extra spaces to make it 16.5mm tall: when placed on your Pi, a PCB will clear the Ethernet and USB jacks. This header has 3mm of pins, compared with our stacking version which is ...

SKU: AF-1658

Connect your own PCB to a Raspberry Pi with this extra-tall female header. The female header part has extra spaces to make it 13.6mm tall: when placed on your Pi, a PCB will clear the Ethernet and USB jacks. This header has 3mm of pins, compared with our stacking version which is the same base...

SKU: EC-RA000022RK

The GPIO extension kit used for extending the GPIO interface on Raspberry Pi B+, it helps you break out all those tasty power, GPIO, I2C and SPI pins from the 40 pin header of Raspberry Pi B+ onto a breadboard.There is also the GPIO board and GPIO Cable for the Model B.Corresponding Interface Pin...

SKU: AF-5294

This 20-pin GPIO ribbon cable provides a clean, reliable connection between PCBs, development boards, and breakout headers. The soft, flexible 0.05″ ribbon cable with keyed IDC connectors on both ends ensures correct orientation every time. Pin 1 is marked with a pink stripe along the side of th...

SKU: AF-4170

A 16-pin (2×8) IDC ribbon cable with keyed connectors on both ends, 305mm (12") long. The 0.05" pitch ribbon cable connects to standard 2×8 0.1" × 0.1" IDC headers. Pin 1 is marked with a white stripe along the cable edge. Key Features 16 Pins (2×8) – Standard IDC ribbon cable layout 305mm (1...

SKU: AF-862

That new Raspberry Pi® Model A or B computer you just got has a row of 2x13 pin headers soldered on - those are the GPIO (general purpose input/output) pins and for those of us who like to hack electronics they are where the real fun is. By programming the Pi, you can twiddle those pins high or l...

SKU: AF-1988

That new Raspberry Pi® Model B+ computer you just got has a row of 2x20 pin headers soldered on - those are the GPIO (general purpose input/output) pins and for those of us who like to hack electronics they are where the real fun is. By programming the Pi, you can twiddle those pins high or low, ...

SKU: AF-2223

Connect your own PCB to a Raspberry Pi B+ and stack on top with this normal-height female header with extra long pins.  The female header part is about 8.5mm tall, good for small HATs that do not to clear the USB/Ethernet jacks. This header has extra long 10mm pins, compared with our p...

SKU: LB-LS3938

This terminal block breakout module comes fully assembled and soldered, ready for use with Raspberry Pi boards.It is compatible with Raspberry Pi 1 Model B+, Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+, Pi 4 Model B, Pi Zero, and Pi Zero W.The module features 2.54 mm (0.1″) pitch terminal blocks su...

SKU: EC-AMC01017B

The A9G development board is a compact IoT module combining GPRS/GSM cellular connectivity with GPS/BDS dual-mode positioning. Based on the A9G module, it supports voice calls, SMS, GPRS data networking, and real-time location tracking — all on a single board. Packed with peripherals including a...

SKU: AF-960

Give your Ultimate GPS V3 a boost with this external active antenna. This GPS antenna draws about 10mA and will give you an additional 28 dB of gain. It's got a 5 meter long cable so it will easily reach wherever you need it to. The antenna is magnetic so it will stick to the top of a car or truc...

SKU: SF-GPS-17519

Many magnetic mount GPS antennas rely on being mounted on a car or other large metallic object to provide a good ground plane. But what if you want to use an antenna not on a car? The GPS Antenna Ground Plate is the solution! This plate significantly increases the performance of GPS and GNSS ante...

SKU: DF-TEL0132

A compact multi-constellation GNSS positioning module based on the AT6558 chip with 32 tracking channels. It simultaneously receives signals from six satellite navigation systems: GPS, BeiDou, GLONASS, Galileo, QZSS, and SBAS (WAAS, EGNOS, GAGAN, MSAS) for accurate joint positioning. The module ...

SKU: WS-8781 · MPN: 8781

Enhance your positioning accuracy with our high-performance GPS External Antenna, designed with an integrated amplifier and superior ceramic technology for optimal signal capture and amplification. Suited for a multitude of positioning and navigational applications, this antenna is the perfect ac...

SKU: SF-GPS-14987

This tri-band GNSS antenna is ideal for GPS L1, GLONASS L1, and Beidou B2 reception. At 45x45mm it is a large ceramic antenna with an incredible 38dB LNA gain.This antenna works well with the GPS-RTK providing reception of Beidou satellites where other more basic GPS antennas cannot. We’ve chosen...