Motor Drivers and Controllers

SKU: PL-5030 | Brand: Pololu

The Motoron M3S256 Triple Motor Controller Shield for Arduino makes it easy to control DC motors from an Arduino or Arduino-compatible board through an I²C interface. Each module can independently control up to three ...

SKU: PR-PIM617 | Brand: Little Bird

A compact motor driver add-on for the Raspberry Pi Pico, based on the DRV8833 dual H-bridge. Solders directly to the back of a Pico and provides two JST-ZH connectors for micro metal gearmotors. Also includes a user b...

SKU: DF-FIT0827 | Brand: DFRobot

The module adopts the standard Modbus RTU protocol, the communication interface supports RS485 or RS232 and supports communication baud rates of 2400, 4800, 9600, 19200, 38400 (default 9600). Each relay output is inde...

SKU: KI-5612 | Brand: Kitronik

Take your robotics project to the next level with the (i2C) Kitronik 16 Servo Driver Board for the BBC micro:bit.Capable of controlling 16 servos which are powered directly from the board's power supply. The board can...

SKU: PL-1383 | Brand: Pololu

Overview The Pololu Simple Motor Controllers are versatile, general-purpose motor controllers for brushed, DC motors. A wide operating range of up to 5.5–40V and the ability to deliver up to several hundred Watts in ...

SKU: KI-5698 | Brand: Kitronik

A compact motor driver board for the BBC micro:bit that drives two DC motors or one stepper motor. The integrated edge connector lets the micro:bit slot in directly, with built-in protection against short circuits, ov...

SKU: EF-EF05070 | Brand: ElecFreaks

The ELECFREAKS Nezha Pro is a micro:bit expansion board designed for education and creative programming. It features a 4-way motor driver, 8 sensor expansion ports, and two built-in motor control buttons that work eve...

SKU: PL-5052 | Brand: Pololu

The Motoron M2H family of dual high-power motor controller add-on boards makes it easy to control up two bidirectional, brushed DC motors with a compatible Raspberry Pi (Model B+ or newer). The M2H controllers are des...

SKU: KI-5693 | Brand: Kitronik

With the Kitronik Compact Robotics Board, the BBC micro:bit can be used to drive 4 motors (or 2 stepper motors) and 8 servos. Coupled with 17 other I/O expansion points, this means the BBC micro:bit can very easily be...

SKU: PL-5063 | Brand: Pololu

The Motoron M1U256 Single I²C Motor Controller offers a compact solution for controlling two DC motors using a UART serial interface. Multiple Motoron controllers can be connected to the same serial bus, making it eas...

SKU: PL-5035 | Brand: Pololu

The Motoron M3H256 Triple Motor Controller makes it easy to control DC motors from a Raspberry Pi (Model B+ or newer) through an I²C interface. Each module can independently control up to three motors, and multiple Mo...

SKU: SF-ROB-09571 | Brand: SparkFun

The SparkFun Serial Controlled Motor Driver allows you to control up to two DC motors using a serial command interface. The serial interface is easy to use and it lets the user select an individual motor, the directio...

SKU: SF-ROB-10507 | Brand: SparkFun

The Quadstepper motor driver board allows you to control up to 4 bipolar stepper motors simultaneously using logic level IO pins. Each motor driver has an output drive capacity of 35V and 1Amps. The board is capable o...

SKU: SF-DEV-09627 | Brand: SparkFun

Developed by Dave Vondle and IDEO Labs, this board is essentially the same as our Power Driver Shield, but the through-hole parts have been switched out for smaller SMD construction, allowing you to to drive high-curr...

SKU: PL-2508 | Brand: Pololu

This shield makes it easy to build an Arduino-controlled Zumo robot. The shield mounts onto an assembled Zumo chassis, connecting directly to the chassis’s battery terminals and motors, and the Arduino plugs into ...

SKU: ON-SERVOEXP | Brand: Little Bird

Add 16 independent PWM outputs to your Onion Omega2 for controlling servos, DC motors, and LED brightness. The onboard 3-pin connectors let you plug in standard servos directly – no breadboard or extra wiring needed. ...