All Products
Showing 1-20 of 29 products · 31 unavailable products hidden
12mm Coin Cell Breakout Board
·
A simple breakout board with a CR1220 coin cell battery holder pre-soldered and broken out to 0.1″ pitch pins. Ideal for powering very low-current projects or providing battery backup for a real-time clock (RTC) module. Comes fully assembled and tested, with a stick of 0.1″ header included so yo...
12mm Coin Cell Breakout w/ On-Off Switch
·
A breakout board with a CR1220 coin cell battery holder, an on/off switch, and 0.1″ pitch breakout pins. Ideal for powering very low-current projects or providing switchable battery backup for a real-time clock (RTC) module. The board breaks out four pins: two ground pins, one switched power pin...
IN100 NanoBeacon Lite Board
·
Build low-power 2.4GHz Bluetooth beacon prototypes with this compact breakout based on the InPlay IN100 NanoBeacon. It is designed for wireless sensor monitoring, asset tracking, retail beacons and DIY beacon tags for real-time location monitoring.The board can run from a single 3V coin cell and ...
Coin Cell Battery Holder - 12mm (SMD)
This is the SMD version of PRT-07948, which is the unit we like to use as RTC backup and SRAM backup for GPS units. Holds battery in place with friction. The metal housing connects to the positive side of the battery and the PCB pad underneath is connected to the negative side.
IN100 NanoBeacon Board with Qwiic
·
This board is a low-power 2.4GHz BT beacon breakout built around the InPlay IN100 NanoBeacon. It is designed for fast deployment in wireless sensor monitoring, asset tracking, retail beaconing and real-time location tag projects where long field life and minimal programming are priorities.Power c...
Sewable CR2032 Battery Holder
·
This sewable CR2032 battery holder makes it easy to add power to wearable electronics projects. Two small 1mm holes in the metal connection tabs are perfectly sized for a #5 or smaller needle to pass through, so you can stitch it directly onto fabric with conductive thread. One tab connects to g...
Battery Holder - 1xAA (PTH)
A PCB-mount clip designed to hold a single AA battery. Ideal for small, low-power applications that need a compact battery solution. Sold individually — use two clips for a complete AA battery holder. Key Features PCB Mount (PTH) – Through-hole solder pins for secure board mounting Single AA ...
Battery Holder - 18650 (PTH)
This is a PCB mount clip to hold a 18650 Lithium Ion Cell battery. Each battery holder is sold in single units, you’ll need two for each battery. These work great for larger, high capacity applications where a drop-in rechargable cell is needed. These little guys are low cost and easy to use! No...
EagLED - Little Bird E-Textile Snippable Board with Buzzer
EagLED is Little Bird Electronics' wearable development kit: an Arduino-compatible microcontroller board with LEDs, a light sensor, push button and buzzer built into a snippable PCB for e-textile projects.Built-in USB support lets you program and power the board from a computer. It works with the...
Teensy to Arduino R3 Shield Adapter
·
This passive adapter lets a Teensy development board connect to the standard Arduino 1.0 (R3) shield footprint, making it easier to reuse existing Arduino shields without a breadboard full of jumper wires.Solder your Teensy board, sold separately, to the marked footprint on the adapter, then plug...
2-Way 18650 Battery Holder
A dual-slot 18650 battery holder with built-in charging and regulated power outputs, perfect for powering microcontrollers, sensors, and portable electronics projects. Simply install two 18650 lithium batteries and use the multiple 5V and 3.3V output ports to run your devices. The holder feature...
1 X AA Battery Holder
This holder provides a simple way to add one AA cell to a battery-powered project. It is moulded in Delrin and uses corrosion-resistant nickel-plated springs and studs for reliable contact.The 150 mm bare lead connection wires make it easy to integrate into prototypes, breadboard builds, portable...
18650 Battery holder without DC connector
A single-cell 18650 battery holder with bare wire leads, designed for easy integration of 18650 lithium-ion cells into your electronics projects. Simply drop in a battery and connect the leads — no soldering or connectors required. Key Features Single 18650 Cell – Holds one standard 18650 batt...
3×AA Battery Holder(PH2.0-2P)
This battery holder connects 3× AA batteries in series, providing approximately 4.5V from alkaline cells. It features a PH2.0-2P connector with a 15cm wire lead, making it compatible with DFRobot boards and other devices that use the PH2.0 power interface. Key Features 3× AA Series Configurati...
Battery Holder - 1x18650 (wire leads)
A single-cell 18650 battery holder with wire leads for easy integration into projects. Drop in an 18650 lithium-ion cell and connect the bare wire leads to your circuit — no soldering to the battery required. Two 6" (150 mm) cables exit from opposite ends of the holder, terminated with bare wire...
2x2 AA Battery Holder with Premium Jumper Header Wires
·
This compact 2×2 AA battery holder connects four AA batteries in series, providing a nominal 6 V DC output (alkaline) or 4.8 V DC (rechargeable NiMH). The premium jumper header wires plug directly into a breadboard — no stripping or soldering required for prototyping. The square 2×2 configuratio...
Adafruit PiRTC - PCF8523 Real Time Clock for Raspberry Pi
·
The Adafruit PiRTC is a battery-backed real-time clock that plugs directly onto your Raspberry Pi's GPIO header, letting your Pi keep accurate time even when powered off. Built around the PCF8523 RTC with native Linux kernel support, it's ideal for data logging, time-stamping, alarms, and any pro...
Battery Holder - 1xAAA (PTH)
PCB mount clip to hold a AAA battery. Sold in single units, you’ll need two for each battery. These work great for small, low power applications that need a battery to run. Low cost and easy to use!Documents:Datasheet
9V battery holder without DC connector
A simple single-slot 9V battery holder case with wire leads for soldering or connecting directly to your projects. Keeps your battery secure and organised. Key Features Wire Leads – Pre-attached cables for direct soldering or breadboard connection Snap-Fit Design – Holds one standard 9V batte...
4xAA Press-Stud Battery Holder - Default
A 4×AA battery holder with press-stud (snap) termination, providing a portable power source for wearable and on-the-go projects. With four alkaline AA batteries, it delivers approximately 6V with 7,000–10,000 mAh of capacity — enough to power an Arduino Uno for over a week. Rechargeable NiMH bat...
