All Products

SKU: AF-5384

This 300 mm (11.8") 4-wire cable is fitted with JST-SH female 4-pin connectors on both ends. The 1 mm pitch JST-SH connectors are more compact than the chunkier 2 mm pitch JST-PH, while still providing a secure latching connection that is easy to insert and remove. Compatible with both STEMMA QT...

SKU: AF-4392

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the JST PH 4 pin. These are the horizontal style. You can use these with any of our JST PH 4 / STEMMA cables. They're not STEMMA QT compatible (those...

SKU: AF-4209

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium Dupont male headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remo...

SKU: AF-5087

A matching pair of 3-pin JST PH compatible cables with inline plug and socket connectors. Each cable is 20 cm long with stranded 26 AWG wires, providing a reliable and compact connection that can carry a couple of amps of current. The friction-lock connectors make it easy to connect and disconne...

SKU: AF-5967 · MPN: ADA5967

The Adafruit Proto Tripler PiCowbell gives your Raspberry Pi Pico or Pico W three side-by-side socket slots — plug in your Pico and up to two PiCowbell accessories with no soldering or stacking headers required. It also includes LiPo battery charging, a power switch, reset button, STEMMA QT conne...

SKU: AF-5906 · MPN: ADA5906

The Adafruit Proto Doubler PiCowbell gives your Raspberry Pi Pico or Pico W two side-by-side socket slots — plug in your Pico on one side and a PiCowbell accessory on the other, no soldering or stacking headers required. It also adds LiPo battery charging, a power switch, reset button, STEMMA QT ...

SKU: AF-5963 · MPN: ADA5963

The Adafruit 555 PWM Output STEMMA is a fully assembled 555 timer board that generates an adjustable square-wave PWM signal — no breadboard wiring or external components needed. An onboard trimmer pot lets you tune the frequency across two selectable ranges: approximately 1.5 KHz to 25 KHz, or 1....

SKU: AF-5580

The Adafruit MAX17048 LiPoly/LiIon Fuel Gauge and Battery Monitor gives you accurate battery voltage and charge percentage readings for your 1S 3.7–4.2V lithium polymer or lithium ion battery. Instead of guessing remaining capacity from a non-linear voltage curve, this smart sensor does the maths...

SKU: SF-PRT-17257

This is a 500mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together but can be used for other applications as well. The cable insulation is made from silicon making it more flexible than our original Qwiic cable particularly in tig...

SKU: DF-FIT0914 · MPN: FIT0914

A 10-pack of PH2.0-4P male-to-male cables for connecting Boson modules, UNIHIKER boards, and other modular electronics. The polarised 4-pin connectors ensure correct orientation and prevent reverse insertion. Key Features Polarised Connectors – Prevents incorrect insertion 4-Pin PH2.0 – Male ...

SKU: AF-4686

The Adafruit TMP235 is a plug-and-play analog temperature sensor with a 3-pin JST PH (STEMMA) connector. Unlike I2C sensors, this one outputs a simple analog voltage proportional to temperature — just connect it to any microcontroller with an analog input and read the value. No libraries or compl...

SKU: AF-5970 · MPN: ADA5970

The Adafruit TSMP96000 "Code Learning" Infrared IR Receiver Breakout detects IR signals across a wide frequency range of 20–60 KHz, making it perfect for "code learning" applications where you need your device to work with any IR remote control — even when you don't know the carrier frequency. U...

SKU: AF-5990 · MPN: ADA5990

The Adafruit Infrared IR Remote Transceiver combines a high-powered IR transmitter and a sensitive 38 kHz IR receiver on a single board. With two 940 nm IR LEDs (one vertical, one horizontal) driven by an onboard N-channel FET at 100–200 mA per LED, you get 10+ metres of transmit range alongside ...

SKU: DF-DFR1083 · MPN: DFR1083

##Introduction The Arduino Portenta C33 is a streamlined module that offers the high performance of the Arduino Portenta family at a lower price point, thanks to optimizations and streamlined features. Ideal to developing cost-effective, real-time applications, the Portenta C33 features the ARM® ...

SKU: AF-4208

A 10-pack of JST SH 4-pin right-angle connectors with 1 mm pitch through-hole mounting tabs. These are the standard connectors used with the Qwiic and STEMMA QT ecosystems, making it easy to add I2C connectivity to your own PCB designs. The solid plastic housing accepts standard Qwiic cables, an...

SKU: SF-PRT-17260

This is a 50mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together but can be used for other applications as well. The cable insulation is made from silicon making it more flexible than our original Qwiic cable particularly in t...

SKU: SF-GPS-23088 · MPN: GPS-23088

The SparkFun Triband GNSS RTK Breakout features Septentrio's mosaic-X5, an ultra-low power multi-band, multi-constellation GNSS receiver capable of delivering centimeter-level precision. Supporting L1, L2, and L5 bands simultaneously, this breakout provides access to GPS, GLONASS, Beidou, Galileo...

SKU: SF-DEV-17712

With a 32-bit ARM® Cortex®-M4 RISC core, the SparkFun STM32 Thing Plus brings power and precision to your projects. The STM32 Thing Plus provides you with an economical and easy to use development platform if you're needing more power with a minimal working space. This Thing comes flashed with t...

SKU: AF-4397

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium female headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.Th...

SKU: SF-GPS-17722 · MPN: GPS-17722

Built around the u-blox ZED-F9P, this MicroMod carrier gives your project high-precision GNSS and RTK positioning in a swappable, solderless MicroMod format. It supports rover and base station operation, with RTK accuracy down to millimetre-level positioning when used with suitable correction dat...