All Products

SKU: SF-DEV-13746

The SparkFun Beefy 3 is an FTDI Basic Breakout board based on the FT231X USB-to-serial IC. Unlike standard FTDI breakouts, it features an AP2112K voltage regulator capable of supplying up to 600mA at 3.3V — enough to power a 3.3V project directly from the board's USB connection. The 6-pin header...

SKU: AF-954

The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. Inside the big USB plug is a USB<->Serial conversion chip and at the end of the 36" cable are four wire - red power, black ground, white RX into USB port, and green TX out of the USB por...

SKU: DF-DFR0734

An industrial-grade RS232 expansion shield designed specifically for the LattePanda V1. Adds one RS232 port (D-Sub 9-pin male) with signal isolation, power isolation, and surge protection for reliable serial communication in demanding environments. Uses a stackable connection with copper standof...

SKU: AF-5446

This USB Type C cable adds a DB-9 (DE-9) serial port to your computer or laptop. Works with MacOS X, Linux, and Windows. Note that this provides (approximately) +-6V serial (RS232) not 5V serial (TTL), good for old devices like GPS, handhelds, programmers, etc with chunky DB9's on the side. Some ...

SKU: DF-FIT0416

Introduction This product converts from USB output to TTL output, supports three levels, facilitates communication between PC and serial port, does not need an external crystal oscillator, has high stability and strong anti-interference. Specification VCC output: 5V/3.3V/1.8V TTL output: 5...

SKU: AF-2471

The Adafruit HUZZAH ESP8266 Breakout is a breadboard-friendly WiFi microcontroller board built around the Espressif ESP8266. With an 80 MHz processor, full WiFi client and access point support, a built-in TCP/IP stack with DNS, and a CE/FCC certified module with on-board antenna, it provides an a...

SKU: AF-3318

Check out this handy USB extension cable, which will make it easy for you to enclose a device that has a Mini-B USB type port. We think this would be most handy when putting a Teensy, FTDI friend, USB LiPo charger, BeagleBone, or any other Mini-B device into a box!This Mini-B male/female extensio...

SKU: AF-3779

The Adafruit AS7262 is a 6-channel visible light spectral sensor from AMS that measures light intensity across six specific wavelength bands: violet (450 nm), blue (500 nm), green (550 nm), yellow (570 nm), orange (600 nm) and red (650 nm). Readings are available as raw 16-bit values or calibrate...

SKU: DF-DFR1226-1 · MPN: DFR1226-1

Built for embedded projects that need desktop-class software support, this palm-sized x86 single-board computer combines an Intel Processor N150 with 8GB of LPDDR5 memory and 64GB of onboard eMMC storage. It keeps the classic LattePanda V1 88mm x 70mm footprint and interface layout, making it a p...

SKU: AF-2378

The Arduino Pro Mini is SparkFun's minimal design approach to Arduino. &nbsp;It's essentially a 5v Arduino that runs an 16 MHz bootloader on a super small, super thin board. &nbsp;There are no connectors attached - allowing you to add whatever connectors or wire you want without too much troub...

SKU: SF-PRT-27882 · MPN: PRT-27882

This adapter lets you use new Alchitry V2 boards with older Alchitry V1 add-on boards. It is designed as a bridge between the updated V2 connector layout and the original V1-style add-on ecosystem.The board has the new style connectors on the bottom for the V2 board, and the old style connectors ...

SKU: AF-4230

A 24-pin 0.5mm pitch FPC extension cable, 25cm long, designed for mounting eInk and ePaper displays at a distance from the driver board. Use this cable when you need to position your display remotely — for example, in a case, frame, or enclosure separate from the main electronics. Simply pry ope...

SKU: DF-DFR0065

This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings ...

SKU: DF-SEN0325

A 6+1 MEMS microphone array built around seven MSM261S4030H0 high-sensitivity digital silicon microphones. Designed for advanced audio applications including noise suppression, echo cancellation, reverb reduction, and sound source localisation. The array outputs raw digital audio over I2S, elimi...

SKU: EC-AP0500STK

AVRISP2.0 STK500 programmer help you download your codes into your controller or bootloader to your Arduino board, it communicates with PC via USB port, and it works with most of PC & notebook computers.Features It can support a wide range of ATMEL AVR microcontroller. It can works with AVR Studi...

SKU: MM-SKU00085

The MonkMakes Slider for micro:bit allows you to interact with your micro:bit by sliding a control left and right. The board uses a 10kΩ linear variable resistor (pot) to output a voltage between 0 and 3V that can be measured in your micro:bit programs using one of the micro:bit connections as a...

SKU: SF-DEV-09718

The FTDI Cable is a USB-to-Serial (TTL level) converter that provides a simple way to connect TTL interface devices to USB. Built around the FTDI FT232RQ chip housed in the USB-A connector, this cable operates at 5V logic levels. The cable terminates in a 0.1" pitch, 6-pin connector commonly use...

SKU: AF-2821

The Feather HUZZAH ESP8266 is an all-in-one Wi-Fi development board with built-in USB and battery charging. Powered by the ESP8266 with a full Wi-Fi stack, it's a compact and affordable way to add Internet connectivity to your projects using the Arduino IDE or NodeMCU Lua. The CP2104 USB-serial ...

SKU: SF-CAB-14909

USB C is quickly becoming more and more prominent in the maker community because, let’s be honest, who likes trying three times to insert USB into a port? This FTDI cable is a USB C to Serial converter which allows for a simple way to connect TTL interface devices to USB. Each 26AWG cable is one ...

SKU: LB-COCKATOO

The Cockatoo is a simple screw-terminal breakout board for the BBC micro:bit. Slide your micro:bit into the edge connector and you get secure screw terminal access to pins 0, 1, 2, 3.3V, and GND — no soldering or crocodile clips required. Screw terminals provide reliable, secure connections for ...