All Products

SKU: AF-284 · MPN: 284

Note: These use genuine FTDI chips, either we purchase them or they are manufactured to our specifications with the requirement of genuine FTDI chips 10/22/14 - read more. Long gone are the days of parallel ports and serial ports. Now the USB port reigns supreme! But USB is hard, and you just wan...

SKU: AF-4172 · MPN: 4172

The Adafruit HUZZAH32 ESP32 Breakout is a compact, breadboard-friendly development board built around the Espressif ESP32 dual-core processor. With WiFi, Bluetooth Classic, and BLE support, 4 MB SPI Flash, and a generous set of GPIO, analog, and communication peripherals, it's a powerful and affo...

SKU: AF-70 · MPN: 70

Just about all electronics use TTL serial for debugging, bootloading, programming, serial output, etc. But it's rare for a computer to have a serial port anymore. This is a USB to TTL serial cable, with a FTDI FT232RL usb/serial chip embedded in the head. It has a 6-pin socket at the end with 5V ...

SKU: AF-4331 · MPN: 4331

Just about all electronics use a UART serial port with RX and TX pins for debugging, bootloading, programming, serial output, etc. But it's rare for a computer to have a serial port anymore. Thus, a serial cable is an essential part of any electrical engineer's toolkit.This is a USB C to TTL seri...

SKU: AF-954 · MPN: 954

The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. Inside the big USB plug is a USB<->Serial conversion chip and at the end of the 36" cable are four wire - red power, black ground, white RX into USB port, and green TX out of the USB por...

SKU: AF-3318 · MPN: 3318

Check out this handy USB extension cable, which will make it easy for you to enclose a device that has a Mini-B USB type port. We think this would be most handy when putting a Teensy, FTDI friend, USB LiPo charger, BeagleBone, or any other Mini-B device into a box!This Mini-B male/female extensio...

SKU: AF-483 · MPN: 483

Detect particles and/or make a cool random number generator with this handsome Geiger counter kit. This easy-to-make pack of parts turns a simple Geiger-Muller tube (included) into a portable blink, beeping radiation detector. You can also connect an FTDI friend to the header, to get serial ou...

SKU: AF-364 · MPN: 364

The PN532 is the most popular NFC chip, and is what is embedded in pretty much every phone or device that does NFC. It can pretty much do it all, such as read and write to tags and cards, communicate with phones (say for payment processing), and 'act' like a NFC tag. If you want to do any sort...

SKU: AF-2471 · MPN: 2471

The Adafruit HUZZAH ESP8266 Breakout is a breadboard-friendly WiFi microcontroller board built around the Espressif ESP8266. With an 80 MHz processor, full WiFi client and access point support, a built-in TCP/IP stack with DNS, and a CE/FCC certified module with on-board antenna, it provides an a...

SKU: AF-2378 · MPN: 2378

The Arduino Pro Mini is SparkFun's minimal design approach to Arduino. &nbsp;It's essentially a 5v Arduino that runs an 16 MHz bootloader on a super small, super thin board. &nbsp;There are no connectors attached - allowing you to add whatever connectors or wire you want without too much troub...

SKU: AF-3779 · MPN: 3779

The Adafruit AS7262 is a 6-channel visible light spectral sensor from AMS that measures light intensity across six specific wavelength bands: violet (450 nm), blue (500 nm), green (550 nm), yellow (570 nm), orange (600 nm) and red (650 nm). Readings are available as raw 16-bit values or calibrate...

SKU: AF-5335 · MPN: 5335

The Adafruit CP2102N Friend is a USB-to-serial converter breakout featuring the Silicon Labs CP2102N chip with USB Type-C. It provides reliable serial communication at up to 3 Mbps, making it ideal for uploading firmware to Arduino, ESP8266, ESP32, and other microcontrollers that use an FTDI-styl...

SKU: AF-2479 · MPN: 2479

The Adafruit Bluefruit LE UART Friend adds Bluetooth Low Energy connectivity to any microcontroller or computer with a hardware or software serial port. With hardware flow control built in, you won't lose data during transmission. Connect via UART TX/RX pins, or use a standard FTDI cable for debu...

SKU: AF-5568 · MPN: 5568

The Adafruit CH9102F Friend is a USB-to-Serial converter breakout featuring the affordable WCH CH9102F chip and a modern USB Type-C connector. It uploads code at up to 3 Mbit/s and includes auto-reset for Arduino/ATmega328 boards — no manual pin manipulation needed. The pinout matches standard F...

SKU: AF-6065 · MPN: ADA6065

The Adafruit CP2105 Friend provides two independent UART serial ports from a single USB-C connection — no USB hub required. Built around the Silicon Labs CP2105 dual-port bridge, it enumerates as two separate COM ports when plugged in, giving you an Enhanced port and a Standard port with differen...

SKU: AF-4970 · MPN: 4970

I²CMini is an easy-to-use, open-source tool for controlling I²C devices over USB, 100% compatible with I²CDriver. Its a small friend that will make working with I2C a breeze, especially if they have a Qwiic/Stemma QT or even Grove I2C connector! USB to I²C interface in a tiny 18x18mm board Can a...