All Products

SKU: LB-LS2202

This compact Bluetooth amplifier board provides wireless audio playback with 5W per channel (10W total) output via dual PAM8403 amplifier chips. Stream music wirelessly from any Bluetooth 5.0 compatible device directly to your speakers. The small form factor and 3mm mounting holes make it easy t...

SKU: SF-DEV-12660

The SparkFun MP3 Player Shield is an awesome MP3 decoder with the capabilities of storing music files onto a run-of-the-mill microSD card, thus giving you the ability toadd music or sound effects to any project. With this board you can pull MP3 files from an microSD card and play them using on...

SKU: AF-1729

This panel-mount RCA cable provides a clean, permanent composite video or audio connection for enclosures and project boxes. Two RCA connectors (one panel-mount, one plug) are joined by a 264 mm (10.4″) cable, with two mounting screws spaced 20 mm apart for secure panel installation. Ideal for c...

SKU: DF-SEN0327

A compact digital MEMS microphone module based on the MSM261S4030H0 chip, providing 24-bit I2S digital audio output. The built-in I2S interface connects directly to DSPs and microcontrollers without requiring an external codec, simplifying audio capture designs. An on-board SK9822 RGB LED provide...

SKU: DF-DFR0119

This compact stereo amplifier module from DFRobot is based on the PAM8403 chip, delivering 3W per channel into 4Ω speakers with over 90% efficiency. It's a fully functional two-channel audio amplifier with an integrated sleep mode that can be controlled via a microcontroller. Operating from 3.6–...

SKU: SF-DEV-13116

The SparkFun Spectrum Shield splits a stereo audio input into 7 frequency bands per channel using two MSGEQ7 graphic equaliser ICs. Read the amplitude of each band via your Arduino's ADC to create sound-reactive projects — from LED visualisers and light shows to sound-activated motors, relays, an...

SKU: DF-DFR0126

This Audio Analyzer module features the MSGEQ7 graphic equalizer display filter.It will give your arduino ears. Sound is broken down into seven frequency bands and the peak level for each band can be read. The seven frequencies measured are as follows: 63Hz, 160Hz, 400Hz, 1kHz, 2.5kHz, 6.25kHz a...

SKU: SF-BOB-11044

This tiny audio amplifier is based on the Texas Instruments TPA2005D1. Its efficient class-D operation means low heat and long battery life. It can drive an 8-Ohm speaker at up to 1.4 Watts; it won’t shake a stadium, but it will provide plenty of volume for your audio projects. The fully-differ...

SKU: LB-PT-M38

A compact Bluetooth 4.2 audio receiver module (MH-M18) that streams two-channel stereo audio wirelessly from your phone, tablet, or other Bluetooth device. Once paired, it delivers lossless audio playback with a connection range of up to 20 metres in open environments. The module supports button...

SKU: SF-COM-13939

A piezo alarm with 16 selectable tone patterns configured via on-board DIP switches. Tone options include continuous, chime, intermittent, warble, and pulsating modes. Capable of producing up to 103 dB(A) at 16 V, making it suitable for audible alarm and alert applications. Key Features 16 Ton...

SKU: AF-4361

Pipe audio in or out of your project with this very handy panel mount audio jack. It's a mono jack with a disconnect pin so you'll get a ground sleeve pin, a left tip pin and a pin that will be disconnected when a jack is inserted. You can use any 3.5mm audio cable with this jack.Each jack comes ...

SKU: EC-CCB25011M

This is a bluetooth audio receiver module with usb and TF card decoding. Usually it’s can be used as a mp3 player, just a TF card and DC 5V power supply. It has five buttons for you to change mode or achieve other audio control like volume adjustment. It has two modes : music mode and bluetooth d...

SKU: SF-SEN-10293

A simple piezo element that can be used as both a sensor and a small audio transducer. When flexed or tapped, it generates a voltage that can be read by a microcontroller, making it ideal for knock and vibration detection projects. Connect the output to an analog input on your Arduino or other m...

SKU: AF-1699

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and Right channels as well as a center ground pin. You can use any 3.5mm stereo cable with this jack. The pins are on 0.1" spacing so it plugs very soli...

SKU: AF-1475

The Raspberry Pi has an on-board audio jack, which is super handy for all kinds of sound effects and speech, just plug and go! However, for when you want better audio for music playback, a USB audio card can greatly improve the sound quality and volume. That's because the on-board audio is genera...

SKU: AF-1798

A 2.5mm stereo (TRS) plug connector for building or repairing custom audio cables. The durable metal construction and flexible spring strain relief ensure a long-lasting, professional result. The 2.5mm plug is a less common size than the standard 3.5mm headphone jack, but is widely used in hands...

SKU: EC-RPA32311R

A high-precision real-time clock (RTC) module based on the DS3231 IC, designed to plug directly into a Raspberry Pi B+ (and compatible with Arduino). The DS3231 maintains accurate timekeeping with ±5 ppm accuracy (±0.432 seconds per day) across −40 °C to +85 °C, and includes a coin cell battery b...

SKU: AF-3351

Listen up! This 2.8" x 1.2" speaker is a great addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like this speaker as it is small and enclosed for good audio volume and quality. It has a handy JST 2PH input ca...

SKU: AF-2793

One truth about working with A/V is you always need the cable or adapter you don't have in your toolbox. That's why we love these terminal-block RCA connectors so much. No soldering required! Use stranded or solid core wire and a small screw driver to create custom wiring jigs. This is the RCA...

SKU: AF-1313

Listen up! This 3" diameter speaker cone is the perfect addition to any audio project where you need an 8 ohm impedance and 1W or less of power. We particularly like this cone as it has 4 handy mounting tabs 60mm apart.Works great with our Wave shield or class D amplifier board.