All Products
Showing 21-40 of 50 products · 10 unavailable products hidden
Gravity: 130 DC Motor Module
INTRODUCTION This DC motor has an integrated transistor built in to the board, eliminating the need for a motor driver. Use PWM to control it for all your DIY project needs. It uses the 3 pin "gravity" interface saving lots of messy wiring. SPECIF...
TT Motor Bi-Metal Gearbox Double Sided Axle and 1:90 Gear Ratio
·
These durable (but affordable!) gearbox motors (also known as 'TT' motors) are an easy, low-cost way to get your projects moving. This is a TT DC Bi-Metal Gearbox Motor with a gear ratio of 1:90, about double the 'standard' 1:48 ratio. That gives them higher torque but slower rotational speed. Si...
SparkFun Quadstepper Motor Driver Board
The Quadstepper motor driver board allows you to control up to 4 bipolar stepper motors simultaneously using logic level IO pins. Each motor driver has an output drive capacity of 35V and 1Amps. The board is capable of driving motors in full, half, quarter, eight, and sixteenth-step modes. The lo...
Big Easy Driver
The Big Easy Driver is a stepper motor driver board for bipolar stepper motors up to 2 A per phase, based on the Allegro A4988 driver chip. Designed by Brian Schmalz, it's the successor to the popular Easy Driver board. It defaults to 16-step microstepping mode and includes onboard 5 V and 3.3 V...
Mini 3-Layer Round Robot Chassis Kit - 2WD with DC Motors
·
A compact three-layer round robot chassis kit with two DC drive motors, matching wheels, and a caster ball for balance. The high-strength anodised aluminium alloy frame provides a sturdy platform for building your own 2WD mobile robot, with three layers of mounting space for batteries, controller...
Adafruit CRICKIT for micro:bit
·
The Adafruit CRICKIT for micro:bit is a robotics and electronics driver board designed for the BBC micro:bit. Plug your micro:bit into the 40-pin edge connector and start controlling motors, servos, solenoids, NeoPixels, capacitive touch sensors, and a speaker — all managed over I2C via the Adafr...
Geared Stepper Motor 5V w/ Driver
These are the popular 28YBJ-48 geared stepper motors with driver board. The motor and driver are suitable for 5V operation. 4 Phase Current : 160 mA per winding (320 mA in 4-step mode) Measured: 250mA stopped, 200 mA running fast Resistance : 31 Ω per coil winding (from Red wire to any coil) ...
TT Motor All-Metal Gearbox - 1:90 Gear Ratio
·
These durable (but affordable!) gearbox motors (also known as 'TT' motors) are an easy, low-cost way to get your projects moving. This is a TT DC All-Metal Gearbox Motor with a gear ratio of 1:90 about double of the 'standard' 1:48 ratio. That gives them higher torque but slower...
DC Motor in Micro Servo Body
·
This tiny DC Motor in Micro Servo Body is an interesting motor - it's the same size and shape as our micro servo but it isn't a servo. It's more like a DC motor + plastic gear-train in a box. It's not a super powerful motor, it would do well as a little robot wheel. It's also a lot less e...
Adafruit A4988 Stepper Motor Driver Breakout Board
·
The Adafruit A4988 Stepper Motor Driver Breakout simplifies stepper motor control down to just two pins — a direction pin and a step pin. Each pulse on the step pin advances the motor by one step or microstep, making it straightforward to achieve precise, controlled motion without complex timer o...
EasyDriver Stepper Motor
The EasyDriver is a simple stepper motor driver board based on the Allegro A3967 IC. It accepts a digital step/direction input (3.3 V or 5 V logic) and drives bi-polar stepper motors (4, 6, or 8 wire) at any voltage within the 7–30 V supply range. The board features adjustable current control fr...
Adafruit USB-C Power Delivery Dummy Breakout - I2C or Fixed
·
This breakout is built around the HUSB238 USB PD sink chip, making it easy to negotiate power from a USB Type-C Power Delivery source without soldering tiny resistors. It plugs into a USB-C cable and uses the CC lines to request a suitable PD voltage.You can configure it with solder jumpers for f...
Adafruit DRV8871 DC Motor Driver Breakout Board - 3.6A Max
·
The Adafruit DRV8871 is a single-channel brushed DC motor driver breakout capable of delivering up to 3.6 A peak current with a wide 6.5–45V motor voltage range. Its resistor-set current limiting and built-in PWM support make it straightforward to use with virtually any brushed DC motor. The boa...
Octagon Chassis Frame - Blue Plastic - 16cm x 16cm x 4cm
·
This Blue Octagon Chassis makes for an excellent robot body that's easy to machine and modify. It's a single piece of 4mm thick plastic, with a variety of holes, slots and cutouts for mounting boards, sensors, and servos. The sides are notched to fit two DC Gear 'TT' motors - you'll want to get f...
MDV 2x2A DC Motor Controller
A dual H-bridge DC motor controller based on the L298N driver chip, capable of driving two bi-directional DC motors at up to 2 A per channel. The module accepts a wide motor supply voltage of 4.8–46V and includes high-speed protection diodes and an enlarged heatsink for improved thermal performan...
Adafruit SPI Non-Volatile FRAM Breakout - 2 Mbit / 256 KBytes - MB85RS2MTA
·
The Adafruit SPI Non-Volatile FRAM Breakout provides 2 Mbit (256 KBytes) of ferroelectric RAM (FRAM) storage over SPI. FRAM combines the non-volatile retention of flash with the instant read/write speed of SRAM — no page writes, no block erasing, and each byte can be written 10 trillion times wit...
Metal DC Geared Motor - 6V 73RPM 2.5Kg.cm
This compact metal DC geared motor features a 99:1 metal gear reduction for high torque output in a small form factor. With a maximum torque of 2.5kg·cm, it's built for robotics, automation, and mechanical projects requiring reliable, durable performance. Specifications Rated Voltage: 6V Oper...
TT Gearbox Motor
·
The classic yellow "TT" plastic gearbox motor, in every gear ratio and lead termination we can get. Dual output shafts, 3–6VDC, and the standard TT footprint that fits every common bracket, wheel and chassis. Choose the gear ratio first The ratio decides the trade between speed and torque. It is ...
Micro Metal DC Geared Motor with Lead Screw (6V 98RPM M3*20)
This DC gearmotor are now in the status of Pre-order and will ship in the end of Jun. This DC gearmotor has an integrated M3*20mm threaded rod as its output shaft, turn it into a linear actuator. 6V rated voltage, the no-load speed could arrive 98RPM, equivalent to 1.1mm/s. The brass facepla...
Adafruit eInk Breakout Friend with 32KB SRAM
·
The Adafruit eInk Breakout Friend is a driver board for eInk/e-paper displays with a standard 24-pin FPC connector. It includes all the power supply circuitry and level shifting needed to connect your favourite display (up to tri-colour 4.2") to any development board via SPI. Unlike basic breako...
