All Products

SKU: SF-BOB-14021

This is the SparkFun RJ11 Breakout, two simple breakout boards for the common 6-pin RJ11 connector. These little boards can easily have one of our RJ11 6-Pin Connectors to work with common telephone cables. Each board features standard B/R/Y/G (Black/Red/Yellow/Green) labels on the top of the ...

SKU: SF-PRT-00132

Through-hole RJ11 socket with PCB mounting posts. 6-pin connection - housing accepts common telephone connectors/wiring. If you need a board for this connector be sure to check out our SparkFun RJ11 Breakout. Two boards are included so be sure to buy two RJ11 connectors to fully utilize them! ...

SKU: SF-PRT-10588

Simple breakout board for the 3.5mm audio jack. Use this breakout (shipped bare) to allow breadboard or SIP access to the super-common 3.5mm audio jack. All five pins are broken out.

SKU: SF-BOB-13906

The SparkFun Multiplexer Breakout provides access to all pins and features of the 74HC4051, an 8-channel analog multiplexer/demultiplexer. The 74HC4051 allows you to turn four I/O pins into eight multifunctional, individually selectable signals, which can be used to do everything from driving eig...

SKU: SF-BOB-00573

This is a full 8-pin breakout for the SIM socket allowing direct access to SIM communication. Note: This breakout board was originally designed for a SIM socket with a switch for card detection. We have since switched to a socket that does not have this feature so the SW1 and SW2 pins have nothin...

SKU: SF-SEN-15335

The SparkFun 9DoF IMU Breakout brings InvenSense's ICM-20948 9-axis motion tracking sensor to a Qwiic-enabled breakout board with an on-board logic level shifter and broken-out GPIO pins. The ICM-20948 is an extremely low-power sensor supporting both I2C and SPI communication, suited for wearable...

SKU: EF-EF05043

The Nezha Breakout Board is a feature-packed expansion board for the micro:bit, designed with classroom use in mind. It integrates 4 servo drivers, 4 motor drivers, and 7 sensor ports — all using RJ11 connectors with foolproof anti-reversal design, so students can plug in confidently without dama...

SKU: SF-BOB-10124

This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount o...

SKU: SF-BOB-11722

This is a clever little breakout board for both the RGB and R/G illuminated rotary encoders. On one side, it breaks out all of the RGB pins to standard, breadboard friendly, 0.1" headers. Turn it over and it has a footprint for the R/G version! Simply solder an encoder down to the board and you’r...

SKU: SF-BOB-15100

Add a USB-C connector to your project without wrestling with tiny SMD pads. This breakout board routes the USB-C connector's key pins to a standard 0.1" pitch header, making it straightforward to integrate into breadboards and custom PCB designs. Breaks out VBUS, GND, CC1, CC2, D+, and D− — cove...

SKU: SF-SEN-18020

The SparkFun LSM6DSO 6 Degrees of Freedom Breakout is an accelerometer and gyroscope sensor with a giant 9kB FIFO buffer and embedded processing interrupt functions. Due to the capabilities and low cost of the LSM6DSO we've created this small breakout board just for you! Each LSM6DSO breakout has...

SKU: SF-BOB-11771

This is a breakout board for the Texas Instruments TXB0104 module. The TXB0104 is a 4-bit bidirectional voltage-level translator with automatic direction sensing. This 4-bit noninverting translator uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA acc...

SKU: SF-BOB-13282

This is a breakout board for the WS2812B RGB LED. The WS2812B is actually an RGB LED with a WS2811 built right into the LED! All the necessary pins are broken out to 0.1" spaced headers for easy bread-boarding. Several of these breakouts can even be chained together to form a display or an addres...

SKU: SF-BOB-09966

A simple breakout board for the USB Mini-B connector, bringing all 5 pins out to a breadboard-friendly 0.1" pitch header. Useful for prototyping USB connections or as a convenient 5V power source (up to 100 mA, unregulated). Key Features All 5 Pins Broken Out – VCC, D-, D+, ID, and GND Breadb...

SKU: SF-GPS-21834

The SparkFun SAM-M10Q GPS Breakout features the SAM-M10Q chip-antenna module from u-blox©. The M10Q line is the successor to u-blox's M8Q found on the SparkFun GPS Breakout - Chip Antenna, SAM-M8Q (Qwiic), and is a drop-in replacement with updated features to reduce power consumption by almost ha...

SKU: EF-EF05049

A pack of five RJ11 modular cables with 4P4C (4-position, 4-contact) connectors on each end. Each cable is 200 mm long and provides a four-wire straight-through connection, suitable for connecting sensors and modules that use the RJ11 interface. Key Features 4P4C Connectors – Standard RJ11 plu...

SKU: SF-LCD-15143

The SparkFun TFT LCD Breakout features a 1.8″ colour display with 128 × 160 pixel resolution and a 4-wire SPI interface. A built-in microSD card holder on the same SPI bus provides storage for images and multimedia files while keeping the pin count low. The breakout accepts both 5 V and 3.3 V po...

SKU: SF-SEN-28869 · MPN: SEN-28869

This anemometer measures wind speed using rotating cups that turn an enclosed magnet. On each rotation, the magnet closes a reed switch, producing a simple pulse output that can be counted by your electronics.The output is available on the two inner conductors of the RJ11 connector, pins 2 and 3....

SKU: SF-SEN-13679

The SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of ...

SKU: SF-BOB-09540

This is a breakout board for the L298N full-bridge dual motor driver; which comes in a staggered, Multiwatt package. All pins of the L298N are broken out to a 15-pin 0.1" pitch header. Two mounting holes are also provided. Dimensions: Board: 1.6x0.85 inches Documents: Schematic Eagle...