All Products
Showing 1-16 of 16 products
JST SH Jumper 4 Wire Assembly - 8
This is a simple four wire cable. Great for jumping from board to board or just about anything else. These cables mate with the connectors listed below. They have bare wires on one end and a 4-pin JST SH connector on the other end with a mating socket.
JST SH Jumper 6 Wire Assembly - 8
This is a simple six wire cable. Great for jumping from board to board or just about anything else. These cables mate with the connectors listed below. They have bare wires on one end and a 6-pin JST SH connector on the other end with a mating socket. Dimensions: 8" length Documents: Datashe...
Adafruit PCA9546 4-Channel STEMMA QT / Qwiic I2C Multiplexer
Need to use multiple I2C devices that share the same address? The PCA9546 4-Channel STEMMA QT / Qwiic I2C Multiplexer lets you connect up to four same-address I2C devices with completely solderless wiring. Five JST SH connectors (1 input + 4 outputs) make it plug-and-play with any STEMMA QT or Qw...
Adafruit Proto Under Plate PiCowBell for Pico
·
The Adafruit Proto Under Plate PiCowbell is a single-slot prototyping base for the Raspberry Pi Pico or Pico W. It provides a reset button, a STEMMA QT / Qwiic connector, a prototyping grid, and double-row socket headers — all with no soldering required when used with a Pico H or Pico WH. The do...
Adafruit Proto Doubler PiCowbell for Pico and PicoW
·
The Adafruit Proto Doubler PiCowbell gives your Raspberry Pi Pico or Pico W two side-by-side socket slots — plug in your Pico on one side and a PiCowbell accessory on the other, no soldering or stacking headers required. It also adds LiPo battery charging, a power switch, reset button, STEMMA QT ...
Adafruit Proto Tripler PiCowbell for Pico and PicoW
·
The Adafruit Proto Tripler PiCowbell gives your Raspberry Pi Pico or Pico W three side-by-side socket slots — plug in your Pico and up to two PiCowbell accessories with no soldering or stacking headers required. It also includes LiPo battery charging, a power switch, reset button, STEMMA QT conne...
Adafruit Feather RP2350
·
The Adafruit Feather RP2350 brings the powerful RP2350 microcontroller to the classic Feather form factor, giving you full compatibility with the entire FeatherWing ecosystem. With dual Cortex-M33 cores running at 150 MHz, 520 KB of SRAM, and 8 MB of flash, this board delivers roughly twice the p...
Adafruit Feather RP2350 with HSTX Port and 8MB PSRAM
·
The Adafruit Feather RP2350 with HSTX Port and 8 MB PSRAM is the upgraded variant of the Feather RP2350, featuring a pre-soldered AP6404L 8 MB PSRAM chip for managing large data buffers, display framebuffers, and memory-intensive applications directly in mappable RAM. Combined with dual Cortex-M3...
JST SH Jumper 6 Wire - 1 Foot
This is a 1 foot long JST SH communication cable which can be cut and hacked to your needs. Ideal if you have a UAV project where the GPS module may be a distance away from the controller board. Cable has two 6-pin JST connectors with 1mm pitch. Wired pin 1 to pin 1.
Adafruit PiCowbell CAN Bus for Pico - MCP2515 CAN Controller
The Adafruit PiCowbell CAN Bus adds CAN bus connectivity to your Raspberry Pi Pico or Pico W, making it easy to interface with automotive, robotics, and industrial sensor networks. Built around the popular MCP2515 CAN controller and TJA1051/3 transceiver, it communicates over SPI and supports bot...
Adafruit DAC6578 Breakout - 8 x Channel 10-bit I2C DAC
·
The Adafruit DAC6578 Breakout provides eight independent 10-bit digital-to-analogue converters in a single package, all controllable over I2C. Set precise output voltages on up to eight channels simultaneously, making it ideal for multi-channel voltage control, LED dimming, or sensor calibration....
Adafruit DAC7578 Breakout - 8 x Channel 12-bit I2C DAC
·
The Adafruit DAC7578 Breakout provides eight independent 12-bit digital-to-analogue converters in a single package, all controllable over I2C. Set precise output voltages on up to eight channels simultaneously, making it ideal for multi-channel voltage control, LED dimming, or sensor calibration....
JST SH 1mm Pitch 3 Pin to Socket Headers Cable - 100mm long
A 100mm adapter cable with a 1mm pitch JST SH 3-pin connector on one end and 0.1" (2.54mm) pitch socket headers on the other. Ideal for connecting to JST SH ports on development boards such as the Raspberry Pi Pico Debug Probe, Pico WH debug port, and other 3-pin JST SH-equipped devices. The soc...
Adafruit PDM Microphone Breakout with JST SH Connector
·
The Adafruit PDM Microphone Breakout with JST SH Connector provides a digital audio input using Pulse Density Modulation (PDM) in a compact, cable-ready form factor. The 4-pin JST SH connector (3V, GND, DAT, CLK) pairs with JST SH cables for flexible microphone placement away from the main board....
Adafruit MAX17048 LiPoly / LiIon Fuel Gauge and Battery Monitor
·
The Adafruit MAX17048 LiPoly/LiIon Fuel Gauge and Battery Monitor gives you accurate battery voltage and charge percentage readings for your 1S 3.7–4.2V lithium polymer or lithium ion battery. Instead of guessing remaining capacity from a non-linear voltage curve, this smart sensor does the maths...
Adafruit QT 3V to 5V Level Booster Breakout - STEMMA QT / Qwiic
The Adafruit QT 3V to 5V Level Booster Breakout lets you connect 3.3 V STEMMA QT / Qwiic devices to sensors and peripherals that require 5 V power or logic. Most modern microcontrollers (ESP32, RP2040, SAMD, micro:bit) run at 3.3 V, but some sensors and modules still need 5 V — this board bridges...
