All Products
Showing 1-20 of 60 products
Electret Microphone - 20Hz-20KHz Omnidirectional
·
This electret capsule microphone is the same one we use in our great microphone amplifier board. It contains a small vibrating element that will output a few milllivolts peak-to-peak. You will need an op-amp to amplify the signal, some chips are designed with the amplifier built in in which...
Electret Microphone Amplifier - MAX4466 with Adjustable Gain
·
A well-designed electret microphone amplifier breakout built around the Maxim MAX4466 op-amp, specifically engineered for microphone amplification with excellent power supply noise rejection. The board comes fully assembled and tested with a 20–20 kHz electret microphone soldered on. A trimmer p...
Electret Condenser Microphone with Washer
·
Add reliable audio input to your digital signal processing projects with this electret condenser microphone and stand-off washer. It has been selected for compatibility with the popular Teensy Audio Adaptor.The included custom laser-cut washer helps with convenient flush mounting directly to the ...
Electret Microphone Amplifier - MAX9814 with Auto Gain Control
·
Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX9814, a specialty chip that is designed for amplifying electret micro...
SparkFun Electret Microphone Breakout
The SparkFun Electret Microphone Breakout pairs a small electret microphone capsule with a 60× OPA344 op-amp preamplifier, making it easy to detect sound with a microcontroller's analogue-to-digital converter. Pick up voice, claps, knocks, or ambient noise — the amplified signal is ready to read ...
SparkFun Analog MEMS Microphone Breakout - SPH8878LR5H-1
The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the SPH8878LR5H-1 analog microphone from Knowles. This board features an OpAmp to bring the output of the microphone to a usable level, allowing you to plug directly into an ADC on a microcontroller or something like the Spar...
6+1 Microphone Array
A 6+1 MEMS microphone array built around seven MSM261S4030H0 high-sensitivity digital silicon microphones. Designed for advanced audio applications including noise suppression, echo cancellation, reverb reduction, and sound source localisation. The array outputs raw digital audio over I2S, elimi...
I2S Microphone Module
A compact digital MEMS microphone module based on the MSM261S4030H0 chip, providing 24-bit I2S digital audio output. The built-in I2S interface connects directly to DSPs and microcontrollers without requiring an external codec, simplifying audio capture designs. An on-board SK9822 RGB LED provide...
Fermion: MEMS Microphone Module
This tiny MEMS microphone has an amplifier gain of 66. When there is no sound detected, it outputs voltage around 0.66*VCC. When speaking, you can easily get the acoustic waveform by ADC sampling. The module can be used on all kinds of 3.3V/5V main-controllers.Connection DiagramSpecificationSigna...
Electret Microphone
Small electret microphone. Useful in acoustic and audio applications. Documents: Datasheet Example Audio LED control project by Adam Greig
Adafruit I2S MEMS Microphone Breakout - SPH0645LM4H
·
The Adafruit I2S MEMS Microphone Breakout features the SPH0645LM4H, a tiny digital MEMS microphone with a purely digital I2S output. Unlike analogue electret microphones, this mic sends digital audio data directly to your microcontroller — eliminating analogue noise and the need for an ADC. With...
Adafruit Silicon MEMS Microphone Breakout - SPW2430
·
The Adafruit SPW2430 Silicon MEMS Microphone Breakout is a compact, low-cost microphone module that detects sound and converts it to an analog voltage — no external bias resistor or amplifier needed. With a frequency range of 100 Hz to 10 kHz, it's well suited for general-purpose audio recording,...
DFRobot SEN0704 6x6 Flexible Tactile Pressure Sensor - UART
·
This flexible thin-film array gives robots, wearables and HCI projects a compact way to sense where pressure is being applied. It integrates 36 independent sensing points into a 15 x 15mm active area, enabling real-time pressure distribution mapping instead of a single force reading.The bendable ...
I2S MEMS Microphone Breakout - ICS-43434
·
Add digital audio input to a capable microcontroller or single-board computer with this tiny breakout for the TDK ICS43434 I2S MEMS microphone. MEMS microphones detect sound like classic electret mics, but are much smaller and thinner, and this one outputs digital I2S audio rather than an analogu...
SparkFun gator:microphone - micro:bit Accessory Board
The SparkFun gator:microphone is a micro:bit Accessory Board that integrates an electret microphone into SparkFun's gator:bit series of gator-clippable accessories, enabling it to be easily interfaced with the micro:bit or other microcontrollers! It provides a binary indication of the presence of...
Wired Miniature Electret Microphone
·
That's one tiny microphone! At about the size of a mature aphid, this wired Electret Microphone is perfect for your FONA. This microphone's very similar to our PCB-mount Elecret Microphone but is significantly smaller and has pre-attached 65mm long wires. We don't have a specific datash...
TensorFlow Lite for Microcontrollers Kit
·
Machine learning has come to the 'edge' - small microcontrollers that can run a very miniature version of TensorFlow Lite to do ML computations. But you don't need super complex hardware to start developing your own TensorFlow models! We've curated a simple kit to dip your toes into machine ...
WM8960 Audio Codec Breakout with Headers (Qwiic)
·
This WM8960 breakout is a low-power stereo audio codec board for adding audio input and output to digital projects. The WM8960 works as both a stereo audio ADC and DAC, using I2S for audio data while allowing settings such as I2S configuration and analogue audio routing to be controlled over I2C....
Me Sound Sensor
Me Sound Sensor is designed to detect the intensity of sound in the surrounding environment. You can use it in sound interative project such as a voice operated switch or build a dancing robot with music. Based on the power amplifier LM386 and the electret microphone, ...
Grove - Sound Sensor
The Sound sensor module is a simple microphone. Based on the power amplifier LM386 and the electret microphone, it can be used to detect the sound strength of the environment. The value of output can be adjusted by the potentiometer. Features Grove compatible interface Wide supply vo...
