All Products
Showing 1-20 of 60 products
MP6550 Single Brushed DC Motor Driver Carrier
The MP6550 from Monolithic Power Systems (MPS) is an H-bridge motor driver IC that can be used for bidirectional control of one brushed DC motor at 1.8 V to 22 V. It can supply up to about 1.7 A continuously and features configurable current sensing and current limiting. Since this board is a car...
2x7A DC Motor Driver
An ultra-compact dual DC motor driver built around a robust H-bridge design with 7 A continuous current per channel and a 50 A peak rating. Opto-coupler isolation on all control signals protects your microcontroller from motor-induced reverse currents, while built-in UVLO (Under-Voltage Latch-Out...
Adafruit TB6612 1.2A DC/Stepper Motor Driver Breakout Board
·
The Adafruit TB6612 Breakout is a compact dual H-bridge motor driver that can spin two DC motors bidirectionally, step one bipolar or unipolar stepper, or fire two solenoids — all at up to 1.2A continuous per channel (3A peak). It's the same driver chip used in the Adafruit Motor Shield and Motor...
L9110H H-Bridge Motor Driver for DC Motors - 8 DIP - 2.5V-12V 800mAh
·
Run two solenoids, or a single DC motor with up to 800mA per channel using the super-simple L9110H H-bridge driver. This bridge chip is an 8 DIP package so it's easy to fit onto any breadboard or perfboard.Each chip contains one full H-bridges (two half H-bridges). That means you can drive 2 sole...
Pololu Dual G2 High-Power Motor Driver 18v18 Shield for Arduino
The Pololu Dual G2 High-Power Motor Driver 18v18 Shield uses pairs of discrete MOSFET H-bridges to drive two large brushed DC motors. It has an Arduino shield form factor for direct plug-in use, and also breaks out all motor driver pins along the left side for standalone operation without an Ardu...
Dual MAX14870 Motor Driver for Raspberry Pi
Control two brushed DC motors directly from your Raspberry Pi with this dual motor driver featuring MAX14870 H-bridge ICs. Capable of handling motors from 4.5V to 36V with up to 1.7A continuous per channel, it's perfect for robotics and motorised projects. This assembled version comes with heade...
DRV8838 Single Brushed DC Motor Driver Carrier
Overview DRV8838 Single Brushed DC Motor Driver Carrier, bottom view with dimensions. TI SN754410 (16-pin DIP) next to the #2135 DRV8835 carrier (14-pin DIP) and #2990 DRV8838 carrier (10-pin DIP) for size reference. Texas Instruments’ DRV8838 is a tiny H-bridge motor driver IC that can...
Thumbnail Sized DC Motor Driver 2x1.5A (HR8833)
INTRODUCTION This is a ultra compact size Dual-H-Bridge dc motor driver (Based on HR8833), which could drive two way 1.5A DC brush motors up to 10V . It has the same footprint as your thumbnail suitable for projects with limited spaces. Both sides of the module are ...
MDV 2x2A DC Motor Controller
A dual H-bridge DC motor controller based on the L298N driver chip, capable of driving two bi-directional DC motors at up to 2 A per channel. The module accepts a wide motor supply voltage of 4.8–46V and includes high-speed protection diodes and an enlarged heatsink for improved thermal performan...
Adafruit DRV8833 DC/Stepper Motor Driver Breakout Board
·
The Adafruit DRV8833 is a dual H-bridge motor driver breakout, capable of driving two DC motors bidirectionally or one bipolar/unipolar stepper motor at up to 1.2 A per channel. It's well suited for low-voltage applications, operating from 2.7V to 10.8V motor power. The DRV8833 features built-in...
Dual Channel H-Bridge Motor Shield-V1.5
The Dual Channel H-Bridge Motor Shield is composed of 2 discrete MOSFET H-bridge, designed to drive two DC motor with max current 8A. It is made up of 8 N-channel MOSFET IRF3205S and 4 pcs of half bridge motor controller IR2104, to build 2 H-bridge. With this shield and the Arduino board, users c...
L298N Dual H-Bridge Motor Driver Board
Using the powerful L298N Dual Motor Driver，this module allows full control of two DC Motors or one stepper-motor. Screw Terminals for easy connections；LEDs show power and output status. Requires six digital inputs. Has 4 mounting holes. Specification: Chip: L298N Maximum Output Curre...
Dual H-Bridge Motor Driver for DC or Steppers - 600mA - L293D
·
Run four solenoids, two DC motors or one bi-polar or uni-polar stepper with up to 600mA per channel using the L293D. These are perhaps better known as "the drivers in our Adafruit Motorshield". If you accidentally damaged the drivers in a shield, you can use one of these puppies to replace it....
Micro bit DRV8833 Motor Driver Expansion Board
The micro:bit DRV8833 Motor Driver Expansion Board adds dual DC motor control to the BBC micro:bit. Built around the DRV8833CPWP motor driver IC, it can output up to 700 mA per channel with four control modes: clockwise rotation, anticlockwise rotation, brake, and stop. The board includes on-boa...
H-Bridge Motor Driver 1A
The SN754410 is a quad half H-bridge motor driver IC capable of driving DC motors, stepper motors, and other inductive loads. It accepts TTL 5V logic inputs and can drive motors from 4.5V to 36V at up to 1A continuous output current per channel. A pin-compatible replacement for the popular L293D...
Adafruit DRV8871 DC Motor Driver Breakout Board - 3.6A Max
·
The Adafruit DRV8871 is a single-channel brushed DC motor driver breakout capable of delivering up to 3.6 A peak current with a wide 6.5–45V motor voltage range. Its resistor-set current limiting and built-in PWM support make it straightforward to use with virtually any brushed DC motor. The boa...
SparkFun Motor Driver - Dual TB6612FNG (1A)
The SparkFun TB6612FNG Motor Driver breakout can independently control up to two DC motors at a constant current of 1.2 A (3.2 A peak). Each motor channel supports four modes — clockwise, counter-clockwise, short-brake, and stop — controlled via two input signals and a PWM speed input. All pins ...
Pololu Dual G2 High-Power Motor Driver 24v14 for Raspberry Pi (Assembled)
The Pololu Dual G2 High-Power Motor Driver 24v14 is a Raspberry Pi expansion board that can independently control two brushed DC motors at up to 14A continuous per channel. It mounts directly onto the Pi's 40-pin GPIO header in the HAT form factor and includes an integrated 5V 2.5A step-down regu...
Motor SHIM for Pico
A compact motor driver add-on for the Raspberry Pi Pico, based on the DRV8833 dual H-bridge. Solders directly to the back of a Pico and provides two JST-ZH connectors for micro metal gearmotors. Also includes a user button and a Qw/ST (Qwiic/STEMMA QT) connector for attaching I²C breakout boards....
MotoMama
MotoMama is an Arduino shield built around the L298N H-bridge driver chip for small motor and robot projects. It can drive two DC motors or one four-wire, two-phase stepper motor.Motor power can be supplied through the onboard power terminal, which can also power the Arduino board. Alternatively,...
