All Products

SKU: SF-GPS-29491 · MPN: GPS-29491

Add dual-band GNSS positioning to a Raspberry Pi or similar single-board computer with this SparkPNT GNSS Flex pHAT and DAN-F10N module combination. It pairs a GNSS Flex pHAT carrier with a u-blox DAN-F10N GNSS Flex Module for metre-level L1/L5 positioning in a compact, swappable format.The pHAT ...

SKU: SF-GPS-19390 · MPN: GPS-19390

This NEO-D9S breakout is an L-Band satellite correction data receiver designed to feed correction streams to a compatible multi-band, high-precision GNSS receiver such as the u-blox ZED-F9P. With a clear view of the sky, especially to the south, it can decode L-Band correction broadcasts and help...

SKU: AF-6311 · MPN: ADA6311

This breakout makes the ANO rotary encoder wheel much easier to use in a breadboard or wired prototype. The encoder is a distinctive navigation control, with a clicky scroll-wheel feel reminiscent of early iPod interfaces.The board converts the encoder’s unusual pin set into a straightforward hea...

SKU: SF-BOB-17110 · MPN: BOB-17110

USB-C is handy for modern projects, but its 24 tiny, tightly spaced pins are not friendly to hand soldering or quick prototyping. This breakout board routes the essential USB-C connections out to a standard 0.1" (2.54mm) pitch so you can work with them on breadboards, perfboards and other prototy...

SKU: SF-BOB-21772 · MPN: BOB-21772

This WM8960 breakout is a low-power stereo audio codec board for adding audio input and output to digital projects. The WM8960 works as both a stereo audio ADC and DAC, using I2S for audio data while allowing settings such as I2S configuration and analogue audio routing to be controlled over I2C....

SKU: SF-DEV-27510 · MPN: DEV-27510

Add the user interface and power features needed to take a compatible SparkFun development board into the field. This shield brings together battery power, charging, storage and controls in a compact add-on board.Power is handled with a LiPo battery connector, charger, fuel gauge and an on/off sw...

SKU: SF-COM-21212 · MPN: COM-21212

Add letters, numbers and symbols to your project with this green 14-segment alphanumeric LED display. Compared with a standard seven-segment display, the extra segments make it much easier to show readable characters as well as numerals.The display uses a common-anode configuration and provides f...

SKU: SF-PRT-26851 · MPN: PRT-26851

Add five-way navigation input to an I2C project without building a button matrix from scratch. Press up, down, left, right or centre on the low-profile directional pad to send button input to your microcontroller.The board uses a PCA9554 8-bit I2C I/O expander to read the momentary buttons, with ...

SKU: AF-5832 · MPN: ADA5832

This breakout brings the INA228 power monitoring chip out to an easy-to-use board for measuring DC current, bus voltage and calculated power on either the high side or the low side of a circuit. It combines a wide common-mode range of up to +85VDC with a 20-bit ADC, giving you precise readings fr...

SKU: RP-PICO-ELEC

If you're looking for a Raspberry Pi Pico Starter Kit, look no further!This is an awesome and affordable electronics kit for the Raspberry Pi Pico.The components of this Pico Electronics Kit enable you to create electronics circuits for light and sound.Pico Breadboarding can be hard, that's wh...

SKU: AF-2465

The PowerBoost 1000C is a DC/DC boost converter with a built-in LiPo battery charger and smart load-sharing circuit. It takes any 3.7V LiIon/LiPoly battery and boosts the output to 5.2V for powering 5V projects like Arduino, Raspberry Pi, or BeagleBone — even while the battery is charging. The l...

SKU: RP-PICO-W-ELEC

If you're looking for a Raspberry Pi Pico W Starter Kit, look no further!This is an awesome and affordable electronics kit for the Raspberry Pi Pico W.The components of this Pico W Electronics Kit enable you to create electronics circuits for light and sound.Pico Breadboarding can be hard, tha...

SKU: LB-LR0013

This RGB LED module gives your microcontroller project a simple way to add full-colour light. It uses a common-cathode through-hole RGB LED, with separate red, green and blue channels for mixing colours.Each colour channel has a built-in current-limiting resistor, helping protect the LED from bur...

SKU: SF-PRT-14493

These are your run-of-the-mill ¼ Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and other prototyping applications, these 100 ohm resistors make excellent pull-ups, pull-downs and current limiters. These thick-lead versions of the resistors fit snugly into a breadboard with...

SKU: EC-ELE18714S

A complete beginner's kit for getting started with Arduino. Built around the UNO R3 development board, this kit bundles everything you need for your first electronics and programming projects — LEDs, resistors, a breadboard, jumper wires, buttons, sensors, and more, all in one package. Fully com...

SKU: AF-3606

The Mongoose OS Google IoT Core Pack is a complete starter kit for building IoT projects with Google Cloud, built around the Adafruit Feather HUZZAH32 (ESP32). Developed in collaboration with Google and Mongoose OS, this kit includes a pre-soldered ESP32 Feather board along with sensors, actuator...

SKU: AF-3588

The Adafruit MetroX Classic Kit is a comprehensive experimentation kit with over 20 guided circuits and projects to explore microcontroller basics. Built around the Adafruit Metro 328 (Arduino UNO-compatible), this kit covers LEDs, transistors, motors, integrated circuits, pushbuttons, sensors, r...

SKU: AF-1994

This 5V 2A USB power supply provides clean, regulated power for single-board computers like the Raspberry Pi and BeagleBone, or any other USB-powered device with high current demands. It outputs via a USB Type-A port, so you can use whatever USB cable your project requires. The supply outputs 5....

SKU: AF-3487

This 30mm translucent green arcade button has built-in LEDs for a beautiful illuminated look. Two surface-mount LEDs with resistors are embedded in the button body, ready to light up from a microcontroller pin or direct 5V power at just 10mA draw. The button screws into place through material up...

SKU: AF-3491

This 30mm translucent clear arcade button has built-in LEDs for a beautiful illuminated look. Two surface-mount LEDs with resistors are embedded in the button body, ready to light up from a microcontroller pin or direct 5V power at just 10mA draw. The button screws into place through material up...