All Products

SKU: SF-PRT-16764

This 2x20 pin female header is meant to allow you to extend the reach of any board with the standard 2x20 GPIO pin footprint like the Raspberry Pi, Google Coral, and NVIDIA Jetson. You can also solder it to Pi HATs that do not have headers on the board. This is assuming that the board is only pop...

SKU: AF-4567 · MPN: 4567

The Adafruit 2.23" Monochrome OLED Bonnet gives your Raspberry Pi a bright, high-contrast display that's easy to read from across the room. Simply plug this pre-assembled bonnet onto any Pi with a 2×20 header and start displaying sharp white text, graphics, and animations at up to 30 FPS. With 1...

SKU: AF-4687 · MPN: 4687

The Adafruit 2.13" Monochrome E-Ink Bonnet brings crisp, paper-like displays to your Raspberry Pi with no soldering required. Simply plug this pre-assembled bonnet onto any Pi with a 2×20 header and start displaying high-contrast black-and-white graphics that remain visible even with power discon...

SKU: SF-DEV-17512

The SparkFun Qwiic pHAT Extension for Raspberry Pi 400 provides access to the Pi 400's GPIO header while adding Qwiic I2C connectivity. The board connects via a 2×20 right-angle header and extends out to the edge of the PCB, allowing you to stack HATs right-side up or connect Qwiic-enabled I2C de...

SKU: WS-19361

Quad GPIO Expander for Raspberry Pi Pico, Four Sets of Male Headers, USB Power Connector Quad GPIO Expander For Pico Four Sets Of Standard Raspberry Pi Pico GPIO Male Headers, USB-Powered Support Features At A Glance Standard Raspberry Pi Pico female header for direct attaching Raspberr...

SKU: AF-6358 · MPN: ADA6358

Build large, colourful HUB75 RGB LED matrix displays from a Raspberry Pi without the usual jumper-wire tangle. This Adafruit Bonnet plugs onto the 40-pin GPIO header and drives three parallel matrix strings using the active3 pinout, so it can handle roughly three times as many panels or pixels as...

SKU: PI-COM0004

This extra-tall 2×20 female header is designed to connect custom PCBs and HATs to the Raspberry Pi GPIO pins. At 16.5 mm tall, it provides enough clearance for your board to sit above the Ethernet and USB jacks without interference. The header has 3 mm pin length on the underside, so there's no ...

SKU: AF-2324 · MPN: 2324

The Adafruit Ultimate GPS HAT adds high-quality GPS and GLONASS positioning to your Raspberry Pi. Built around a PA1616D module, it provides precise location data and a built-in real-time clock (RTC) with coin cell backup — perfect for outdoor projects, time synchronisation, and location-aware ap...

SKU: PR-PIM138

If music be the food of love, play on. But make sure you use this super little DAC to get the best out of your Raspberry Pi audio! This pHAT provides a super affordable high-quality DAC for your Raspberry Pi. It pumps out 24-bits at 192KHz from the Raspberry Pi's I2S interface on its 2x20 pin ...

SKU: AF-4905 · MPN: 4905

A 40-pin FPC to straight 2×20 IDC female socket header adapter board. Converts a standard 40-pin 0.5mm pitch FPC/FFC cable connection into a Raspberry Pi-compatible GPIO socket, allowing you to extend or relocate your Pi's GPIO header using a slim, flexible cable. Plug the female socket directly...

SKU: AF-4909 · MPN: 4909

A 40-pin FPC to right-angle 2×20 IDC female socket header adapter board. Converts a standard 40-pin 0.5mm pitch FPC/FFC cable connection into a Raspberry Pi-compatible GPIO socket, allowing you to extend or relocate your Pi's GPIO header using a slim, flexible cable. Plug the female socket direc...

SKU: WS-30901 · MPN: 30901

Power your Raspberry Pi 5 or Compute Module 5 over Ethernet with this PoE HAT (H). Deliver both power and network connectivity through a single Ethernet cable—perfect for remote installations, clean setups, and locations without easy access to power outlets. The HAT features an isolated switched-...

SKU: AF-1658 · MPN: 1658

Connect your own PCB to a Raspberry Pi with this extra-tall female header. The female header part has extra spaces to make it 13.6mm tall: when placed on your Pi, a PCB will clear the Ethernet and USB jacks. This header has 3mm of pins, compared with our stacking version which is the same base...

SKU: LB-LS3507

This 2×20 pin tall female header extends the reach of any board with a standard 40-pin GPIO layout, including the Raspberry Pi, Google Coral, and NVIDIA Jetson. At 16 mm tall with standard 0.1″ (2.54 mm) spacing, it provides significant clearance for stacking boards or fitting into enclosures. C...

SKU: LB-LS3938

This terminal block breakout module comes fully assembled and soldered, ready for use with Raspberry Pi boards.It is compatible with Raspberry Pi 1 Model B+, Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+, Pi 4 Model B, Pi Zero, and Pi Zero W.The module features 2.54 mm (0.1″) pitch terminal blocks su...

SKU: AF-2223 · MPN: 2223

Connect your own PCB to a Raspberry Pi B+ and stack on top with this normal-height female header with extra long pins.  The female header part is about 8.5mm tall, good for small HATs that do not to clear the USB/Ethernet jacks. This header has extra long 10mm pins, compared with our p...

SKU: RP-SC0020 · MPN: SC0020

The Raspberry Pi Zero W is the wireless version of the ultra-compact Raspberry Pi Zero, adding built-in WiFi (802.11 b/g/n) and Bluetooth 4.1 (with BLE) via a BCM43143 chip. It retains the same tiny form factor and low price point as the Pi Zero v1.3, making it an excellent choice for IoT project...

SKU: AF-4863 · MPN: 4863

The Adafruit CYBERDECK HAT is a GPIO extender for the Raspberry Pi 400 that lets you plug full-size HAT displays and add-on boards into the back of the Pi 400 at a convenient angle. It duplicates every GPIO pin from input to output, so your HATs work without any pin limitations. In addition to t...

SKU: AF-1601 · MPN: 1601

The Adafruit PiTFT 2.8" is a colour touchscreen display designed for the Raspberry Pi. Featuring a 2.8-inch 320×240 pixel TFT with 16-bit colour and a resistive touch overlay, it works as a mini console, X Window display, image viewer, or video player — all driven over the Pi's high-speed SPI int...

SKU: AF-3422 · MPN: 3422

The Adafruit Arcade Bonnet makes it easy to build retro gaming projects with a Raspberry Pi. It's sized to match the Pi Zero for compact builds, but works with any Pi that has a 2×20 header (Pi Zero, Pi 2, Pi 3, Pi B+, etc.). The bonnet manages all buttons and switches through an I2C GPIO expand...