All Products

SKU: AF-2000 · MPN: 2000

Note: The Pro Trinket's bit-bang USB technique is a legacy approach that may not work reliably with modern operating systems. For new projects, consider an ItsyBitsy or Metro Mini board with native USB support at a comparable price. The Adafruit Pro Trinket 5V is a compact ATmega328P-based mic...

SKU: AF-2378 · MPN: 2378

The Arduino Pro Mini is SparkFun's minimal design approach to Arduino.  It's essentially a 5v Arduino that runs an 16 MHz bootloader on a super small, super thin board.  There are no connectors attached - allowing you to add whatever connectors or wire you want without too much troub...

SKU: AF-2124 · MPN: 2124

The Adafruit Pro Trinket LiIon/LiPoly Backpack is a tiny add-on board that sits on top of your Pro Trinket or ItsyBitsy, adding rechargeable LiPo battery support with automatic charging and power switching. When USB is connected, the battery charges automatically. Unplug USB and it seamlessly swi...

SKU: AF-2010 · MPN: 2010

Note: The Pro Trinket's bit-bang USB technique is a legacy approach that may not work reliably with modern operating systems. For new projects, consider an ItsyBitsy or Metro Mini board with native USB support at a comparable price. The Adafruit Pro Trinket 3V is a compact ATmega328P-based mic...

SKU: AF-5302 · MPN: 5302

The Adafruit KB2040 is an RP2040-powered board designed specifically for mechanical keyboard builds, in the Arduino Pro Micro form factor. With castellated pads, USB-C, 8 MB of Flash, and a STEMMA QT / Qwiic connector, it's a drop-in replacement for Pro Micro boards with significantly more power ...

SKU: AF-6080 · MPN: ADA6080

Built around Raspberry Pi’s RP2350 processor, this Cytron robotics controller is made for beginner and intermediate builders who want to create more advanced robots while spending less time on the supporting electronics.The board integrates a 4-channel brushed DC motor driver, servo outputs, GPIO...

SKU: AF-4364 · MPN: 4364

Just about all electronics use a UART serial port with RX and TX pins for debugging, bootloading, programming, serial output, etc. But it's rare for a computer to have a serial port anymore. Thus, a serial cable is an essential part of any electrical engineer's toolkit.This is a USB C to TTL seri...

SKU: AF-5460 · MPN: 5460

You might recognize this interesting new component from behind-the-scenes studio clips of audio recording equipment or even music videos. A fader is a control device for fading or changing the sound volume, light intensity, or simply the gain on an audio or video signal.Here is a small, black han...

SKU: AF-4331 · MPN: 4331

Just about all electronics use a UART serial port with RX and TX pins for debugging, bootloading, programming, serial output, etc. But it's rare for a computer to have a serial port anymore. Thus, a serial cable is an essential part of any electrical engineer's toolkit.This is a USB C to TTL seri...

SKU: AF-5401 · MPN: 5401

Introducing the ProS3 - The Ultimate Pro ESP32-S3 Development Board The ProS3 ships with the latest version of CircuitPython with ESP32-S3 support. It also ships with the UF2 bootloader, so you can easily update your ProS3 with the latest CircuitPython firmware, whenever you desire. Just plug you...

SKU: AF-3574 · MPN: 3574

The Feather nRF52 Pro is an advanced Bluetooth Low Energy development board built around the Nordic nRF52832, designed specifically for use with the Apache Mynewt RTOS. It features a fully open-source BLE 5.0 stack, a serial bootloader for command-line firmware flashing, and an on-board SWD debug...

SKU: AF-3406 · MPN: 3406

The Feather nRF52 Bluefruit LE is an all-in-one Bluetooth Low Energy development board built around the Nordic nRF52832. Unlike earlier Bluefruit Feathers that used a separate helper chip, the nRF52832 runs your application code and handles BLE directly — resulting in lower power consumption, low...

SKU: AF-5403 · MPN: 5403

Piunora by Diode Delights is a compact, easy-to-use development board for electronics prototyping with Linux. It has a familiar form factor, legible pin labels, and a design that’s well suited to space-constrained applications.As a carrier board for the Raspberry Pi Compute Module 4 (CM4), Piuno...

SKU: AF-6360 · MPN: ADA6360

This SmartiPi Touch Pro 3 enclosure is designed for the Raspberry Pi Touch Display 2, giving your touchscreen project a tidy, mountable case with room inside for extra hardware. It is compatible with Raspberry Pi 3, 4 and 5 boards.This version includes the Small 25mm deep cover. SmartiPi also off...

SKU: AF-4062 · MPN: 4062

The Feather nRF52840 Express upgrades the nRF52 Bluefruit with the Nordic nRF52840 — featuring 1 MB flash, 256 KB SRAM, native USB, and Bluetooth Low Energy in a single chip. Native USB means no separate serial converter is needed; the chip handles CDC serial, and can also act as a HID keyboard, ...

SKU: PR-PIM175

The Explorer HAT Pro is a feature-packed add-on board for Raspberry Pi that brings together digital I/O, analog inputs, capacitive touch, motor drivers, LEDs, and a mini breadboard — all on a single HAT. It's ideal for robotics, games, science experiments, and learning electronics with the Pi. K...

SKU: AF-4951 · MPN: 4951

Here is an updated, excellently designed stand that provides a sleek and sturdy look for the 7" Touchscreen Display and Raspberry Pi. Say hello to the improved SmartiPi Touch Pro! The SmartiPi Touch Pro is a case for the Official Raspberry Pi display and Raspberry Pi 2, 3, and...

SKU: AF-5026 · MPN: 5026

This mounting plate kit is an affordable, simple solution to mounting your Raspberry Pi 4 or Model 3 B+ to your Raspberry Pi HQ Camera.  Easy to assemble, the plate attaches to your HQ Camera on one side, and your Raspberry Pi mounts to the other side – spacers and fixings are incl...

SKU: AF-349 · MPN: 349

Make cables and wiring harnesses with ease using the best crimping pliers we've used. These precision machined crimpers will turn you into a pro, no more painful struggles with pliers and generic crimpers that smoosh your contacts so they wont fit properly. This model does a wide range of the ...

SKU: AF-3097 · MPN: 3097

Looking to improve the printing bed on your Flashforge Creator Pro? Check out the PRINTinZ Skin for Flashforge! The PRINTinZ Skin is a peel and stick surface for 3D printer beds made from the same durable material as the outer layers of the Plate. It's the perfect optio...