Sensors

SKU: DF-DFR0023 | Brand: DFRobot

This is an Arduino Temperature Sensor based on LM35 temperature chip. A Temperature Sensor can be used to detect ambient air temperature.The LM35 chip is produced by National Semiconductor Corporation and offers a fun...

SKU: DF-SEN0043 | Brand: DFRobot

An analog ambient light sensor based on the TEMT6000 detector, which has a spectral response closely matching the human eye with very low IR sensitivity. It outputs an analog voltage proportional to the ambient light ...

SKU: DF-DFR0067 | Brand: DFRobot

This Gravity-compatible DHT11 sensor provides calibrated digital temperature and humidity readings via a single data pin. With an integrated 8-bit microcontroller and factory-calibrated coefficients stored in OTP memo...

SKU: AF-1083 | Brand: Adafruit

Add high-speed analog-to-digital conversion to any microcontroller with the ADS1015 breakout. This 12-bit ADC delivers 3,300 samples per second over I2C, with four single-ended or two differential input channels and a...

SKU: DF-DFR0034 | Brand: DFRobot

This is a new Arduino compatible Analog Sound Sensor. Sound Sensor is typically used in detecting the loudness in ambient, the Arduino can collect its output signal and actuate accordingly. You may use it to make some...

SKU: DF-SEN0209 | Brand: DFRobot

This is an Arduino compatible piezo film vibration sensor. It is made up of flexible piezo film and converter board. The sensor is able to detect vibration, flexibility, impact and touch. The film is a flexible compo...

SKU: SF-BOB-19389 | Brand: SparkFun

The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the SPH8878LR5H-1 analog microphone from Knowles. This board features an OpAmp to bring the output of the microphone to a usable level, allowing ...

SKU: SF-BOB-13878 | Brand: SparkFun

The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire Wheatstone bridge configuration. If you open up an electronic bathroom scale, you’ll find a large rat’s ne...

SKU: AF-5913 | Brand: Adafruit

The Adafruit STEMMA Reflective Photo Interrupt Sensor uses a TCRT1000 right-angle optical module to detect reflective surfaces. An onboard IR LED emits light, and when an object reflects it back to the IR phototransis...

SKU: DF-SEN0487 | Brand: DFRobot

This tiny MEMS microphone has an amplifier gain of 66. When there is no sound detected, it outputs voltage around 0.66*VCC. When speaking, you can easily get the acoustic waveform by ADC sampling. The module can be us...

SKU: LB-24-THERMISTOR | Brand: Little Bird

A thermistor changes its resistance with temperature. Find our tutorial here A thermistor is a type of variable resistor whose resistance changes with temperature. Let's take a closer look at the thermistor module....

SKU: DF-DFR0588 | Brand: DFRobot

Gravity: Analog SHT30 Temperature & Humidity Sensor adopts the new generation SHT30 temperature and humidity sensor from Sensirion. Thanks to Sensirion's CMOSens® technology, highly integrated capacitive humidity sens...

SKU: AF-2716 | Brand: Adafruit

The Adafruit SPW2430 Silicon MEMS Microphone Breakout is a compact, low-cost microphone module that detects sound and converts it to an analog voltage — no external bias resistor or amplifier needed. With a frequency ...

SKU: PL-1479 | Brand: Pololu

This carrier board is designed to work with any of the MQ-series gas sensors, simplifying the interface from 6 to 3 pins—ground, power and analog voltage output—that are broken out with a 0.1" spacing, making the boar...

SKU: SF-SEN-13968 | Brand: SparkFun

The SparkFun OpenPIR is a highly customizable Passive Infrared (PIR) sensor based around the NCS36000 PIR controller. Passive infrared (PIR) sensors are able to detect motion in a small/local area –– they’re the senso...

SKU: SF-DEV-13956 | Brand: SparkFun

The SparkFun Weather Shield is an easy-to-use Arduino shield that grants you access to barometric pressure, relative humidity, luminosity and temperature. There are also connections on this shield to optional senso...

SKU: DF-DFR1132 | Brand: DFRobot

##Introduction Gravity: Linear/Analog Hall Sensor is a high-precision device designed for measuring and monitoring magnetic field strength. Advanced Hall effect circuitry at the core converts magnetic induction streng...

SKU: EF-EF05032 | Brand: ElecFreaks

An alcohol vapour sensor module from the ELECFREAKS PlanetX range, designed for use with micro:bit via an RJ11 connector. The MQ3 sensor uses a tin dioxide (SnO2) sensing element whose conductivity increases with alco...

SKU: EF-EF05018 | Brand: ElecFreaks

An analogue trimpot (trimmer potentiometer) sensor module from the ELECFREAKS PlanetX series, designed for use with micro:bit via RJ11 connection. The potentiometer provides stepless rotation over a 0°–300° range, out...

SKU: SF-SEN-24048 | Brand: SparkFun

A line follower sensor gives your robot the ability to detect lines or nearby objects. The sensor works by detecting reflected light coming from its own infrared LED. By measuring the amount of reflected infrared ligh...