Sensors

SKU: DF-SEN0032 | Brand: DFRobot

Breakout board for the Analog Device ADXL345. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos ...

SKU: DF-SEN0129 | Brand: DFRobot

INTRODUCTION This is an Arduino CH4 gas sensor. It uses MQ4 probe which is able to detect nature gas, CH4. It is less sensitivity in detecting alcohol, cooking fumes, and cigarette smok...

SKU: SF-COM-10601 | Brand: SparkFun

An insulated reed switch that closes when exposed to a magnetic field and opens when the field is removed. The encapsulated design is more durable than glass reed switches and can be easily populated on a PCB. Key Fe...

SKU: DF-SEN0017 | Brand: DFRobot

This is a line tracking (following) sensor to guide your robot by telling white from black quickly and accurately. It is commonly used in arduino robot project, and probably is the best line following sens...

SKU: SF-ROB-09453 | Brand: SparkFun

This version of the QRE1113 breakout board features an easy-to-use analog output, which will vary depending on the amount of IR light reflected back to the sensor. This tiny board is perfect for line sensing applic...

SKU: DF-DFR0076 | Brand: DFRobot

This Gravity analog flame sensor detects fire and infrared light sources in the 760–1,100 nm wavelength range. With a 60° detection angle and analogue output proportional to flame distance, it's widely used in firefig...

SKU: AF-3386 | Brand: Adafruit

The Adafruit PiRTC is a battery-backed real-time clock that plugs directly onto your Raspberry Pi's GPIO header, letting your Pi keep accurate time even when powered off. Built around the PCF8523 RTC with native Linux...

SKU: AF-5990 | Brand: Adafruit

The Adafruit Infrared IR Remote Transceiver combines a high-powered IR transmitter and a sensitive 38 kHz IR receiver on a single board. With two 940 nm IR LEDs (one vertical, one horizontal) driven by an onboard N-ch...

SKU: DF-SEN0564 | Brand: DFRobot

The Fermion MEMS Carbon Monoxide Sensor uses micro-electromechanical system (MEMS) technology to detect CO gas concentrations from 5 to 5,000 ppm. Its compact size, low power consumption, short preheat time, and fast ...

SKU: DF-SEN0546 | Brand: DFRobot

This I2C digital temperature & humidity sensor offers high accuracy of ±3.0RH% for humidity and ±0.5°C for temperature and features a user-programmable humidity & temperature alarm function.Its housing is made of 304 ...

SKU: AF-5464 | Brand: Adafruit

This rubber sheet is made of the same carbon-black impregnated rubber material that our conductive rubber cord uses. Traditionally it would be used for EMF shielding, or conductive gaskets - but it's very fun to play ...

SKU: AF-5425 | Brand: Adafruit

The Adafruit VL53L4CX is the longest-range Time-of-Flight (ToF) distance sensor in ST's VL5 series, measuring from approximately 1 mm up to 6000 mm (6 metres). It uses an invisible laser to precisely time how long lig...

SKU: LB-LS2708 | Brand: Little Bird

The AGS02MA is a MEMS-based TVOC (Total Volatile Organic Compounds) gas sensor with a calibrated digital signal output. It detects a range of polluting gases including ethanol, ammonia, sulfides, benzene vapours, and ...

SKU: DF-SEN0335 | Brand: DFRobot

Build up a simple environmental monitor station with this multi-function environment sensor! Based on the combination of CCS811+BME280 chip, this module features high accuracy, I2C interface, and fast Measurement. ...

SKU: AF-4226 | Brand: Adafruit

The Adafruit INA260 is a precision DC power sensor that measures current, voltage, and power on either the high or low side of your circuit. With an integrated 2 mΩ (0.002Ω) 0.1% shunt resistor and 16-bit ADC, it hand...

SKU: AF-3965 | Brand: Adafruit

The Adafruit MPRLS Ported Pressure Sensor Breakout measures absolute air pressure from 0 to 25 PSI (0–172 kPa) via a stainless steel port. Unlike typical barometric sensors, the metal port lets you attach tubing to me...

SKU: LB-LR0022 | Brand: Little Bird

It's a push button!A push button with resistors and breadboard friendly layout.**Push Button Pinout:**- Signal (High when button pushed)- Positive- Ground**Specifications:**- 600mW MAX (50mA at 12v)

SKU: SF-COM-08636 | Brand: SparkFun

The MCP3002 is a 10-bit analog-to-digital converter (ADC) with a simple SPI interface, available in a breadboard-friendly 8-pin DIP package. Use it to add analog input capability to microcontrollers that lack an ADC, ...

SKU: SF-SEN-00246 | Brand: SparkFun

This sensor uses an infrared emitted diode combined with an infrared phototransistor to detect the reflected infrared signal. Ideal for sensing black-to-white transitions or can be used to detect nearby objects (.5-1cm).

SKU: DF-DFR0023 | Brand: DFRobot

This is an Arduino Temperature Sensor based on LM35 temperature chip. A Temperature Sensor can be used to detect ambient air temperature.The LM35 chip is produced by National Semiconductor Corporation and offers a fun...