Sensors & Input

SKU: DF-SEN0168 | Brand: DFRobot

This Triple Axis Accelerometer with Bosch BMA220 is an ultra small triaxial, low-g acceleration sensor breakboard with SPI and I2C interface, aiming for low power consumer market applications. It allows measurem...

SKU: SF-SEN-13322 | Brand: SparkFun

The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straight forward to use. The two large exposed pads function as probe...

SKU: SF-SEN-13285 | Brand: SparkFun

This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the ‘alarm’ pin will go low.This unit works great from 5...

SKU: AF-334 | Brand: Adafruit

If you've got a resistive touch screen that you'd like to use, you'll need this breakout! It has a fine pitch (0.5mm) connector soldered onto it and it's broken out into the 4 resistive wires of the panel. A petite...

SKU: SF-SEN-13266 | Brand: SparkFun

The SparkFun MAX31855K Thermocouple Breakout is a simple 14-bit resolution, SPI-compatible, serial interface thermocouple digitizer that makes reading a wide range of temperatures possible. A thermocouple works by ...

SKU: AF-360 | Brand: Adafruit

This blank 13.56 MHz RFID/NFC white tag is a compact disc-shaped token commonly used for laundry tracking, garment identification, and asset tagging. It contains a Mifare Classic 1K chip with 1 KB of writable EEPROM s...

SKU: SF-SEN-11084 | Brand: SparkFun

Life has its ups and downs, so why not measure them? The MPL3115A2 is a MEMS pressure sensor that provides Altitude data to within 30cm (with oversampling enabled). The sensor outputs are digitized by a high reso...

SKU: AF-374 | Brand: Adafruit

These 1-wire digital temperature sensors are fairly precise (±0.5°C over much of the range) and can give up to 12 bits of precision from the onboard digital-to-analog converter. They work great with any microcontro...

SKU: AF-386 | Brand: Adafruit

The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no an...

SKU: SF-SEN-11005 | Brand: SparkFun

This non-invasive current sensor (also known as a split-core current transformer) clamps around the supply line of an electrical load to measure how much current is flowing through it. The sensor acts as an inductor, ...

SKU: AF-444 | Brand: Adafruit

Add a tiny joystick to your project with this PSP thumbstick. This is a replacement component for PSP1000's, but we think they'd make for a great little joystick/thumbstick add-on for a wearable, or portable pro...

SKU: SF-SEN-13030 | Brand: SparkFun

The SparkFun RFID Reader Breakout converts the 2mm pin spacing of ID-series RFID readers to breadboard-friendly 0.1" headers. Compatible with the ID-3LA, ID-12LA, and ID-20LA readers, this board lets you solder the re...

SKU: DF-SEN0177 | Brand: DFRobot

The Gravity Laser PM2.5 Air Quality Sensor uses laser scattering to measure suspended particulate matter concentrations in the air. It detects particles from 0.3 to 10 µm in diameter and outputs digital concentration ...

SKU: DF-FIT0454 | Brand: DFRobot

This is a small built-in spring GSM antenna with IPX connector. Its working frequency is 900/1800 MHz which meets most requirements of GSM applications. Its very compact size makes it easy to carry and use. ...

SKU: SF-BOB-10160 | Brand: SparkFun

Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time clock with an integrated temperature-compensated crystal oscillator and crystal. Th...

SKU: AF-705 | Brand: Adafruit

A compact 3-wire voltage meter with a vivid green 3-digit 7-segment display. Reads 0–99.9VDC with 0.1V precision, making it perfect for monitoring battery levels, power supplies, and electronic projects. Mounting tabs...

SKU: AF-1918 | Brand: Adafruit

An analog UV light sensor breakout based on the GUVA-S12SD photodiode, detecting the 240–370nm range covering UVB and most of the UVA spectrum. An on-board op-amp amplifies the tiny photodiode current to a readable vo...

SKU: DF-SEN0018 | Brand: DFRobot

This is a simple to use arduino motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the 'alarm' pin will go low. This sensor c...

SKU: DF-SEN0220 | Brand: DFRobot

The Gravity UART Infrared CO2 Sensor uses non-dispersive infrared (NDIR) technology to measure carbon dioxide concentrations from 0 to 50,000 ppm. It offers excellent selectivity with no oxygen dependency, built-in te...

SKU: DF-DFR0053 | Brand: DFRobot

This arduino Slide Position Sensor is based on straight-slip slide potentiometer sensor. The sensor is able to give provide the position of the slider which is often considered as a linear potentiometer . The ...