Sensors & Input

SKU: AF-3942 | Brand: Adafruit

The HC-SR04 is an ultrasonic distance sensor that measures distances from approximately 2 cm to 400 cm (best results between 10–250 cm). Widely used in robotics, automation, interactive art, and motion sensing project...

SKU: DF-SEN0240 | Brand: DFRobot

The Gravity Analog EMG Sensor by OYMotion detects surface electromyography (sEMG) signals to measure muscle and neural activity. The sensor amplifies the tiny sEMG signal (±1.5 mV) by 1000× and filters noise through d...

SKU: AF-1602 | Brand: Adafruit

Add lots of touch sensors to your next microcontroller project with this easy-to-use 8-channel capacitive touch sensor breakout board, starring the CAP1188. This chip can handle up to 8 individual touch pads, and has ...

SKU: AF-2340 | Brand: Adafruit

The Adafruit Capacitive Touch HAT adds 12 capacitive touch sensors to your Raspberry Pi using the MPR121 touch controller over I2C. Each sensor has a figure-8 hole designed for alligator clip connections — attach clip...

SKU: DF-SEN0237-A | Brand: DFRobot

This is a dissolved oxygen sensor kit, which is compatible with Arduino microcontrollers. This product is used to measure the dissolved oxygen in water, to reflect the water quality. It is widely applied in many wa...

SKU: DF-FIT0180 | Brand: DFRobot

This type of photoresistor is made of environment-friendly materials(no Cadmium and Lead) compared with the traditional CDS photoresistor. It changes resistance depending on the amount of light it is exposed to. Thes...

SKU: AF-2773 | Brand: Adafruit

Have your next project be controlled by your muscles with this pack of Muscle Sensor Surface EMG Electrodes! Pair the electrodes with the MyoWare Muscle Sensor and a microcontroller (ie. Arduino...

SKU: AF-2809 | Brand: Adafruit

The Adafruit LIS3DH is a popular, low-power triple-axis accelerometer breakout packed with features typically found only on higher-end sensors. With selectable measurement ranges, multiple interface options, and built...

SKU: SF-BOB-08688 | Brand: SparkFun

Basic breakout board for the TEMT6000 Ambient Light Sensor. Only what you need, nothing you don’t. Sensor acts like a transistor - the greater the incoming light, the higher the analog voltage on the signal pin. Docu...

SKU: SF-SEN-08606 | Brand: SparkFun

A simple flex sensor 4.5" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the original Nintendo Power Gl...

SKU: SF-BOB-13906 | Brand: SparkFun

The SparkFun Multiplexer Breakout provides access to all pins and features of the 74HC4051, an 8-channel analog multiplexer/demultiplexer. The 74HC4051 allows you to turn four I/O pins into eight multifunctional, indi...

SKU: SF-BOB-13878 | Brand: SparkFun

The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire Wheatstone bridge configuration. If you open up an electronic bathroom scale, you’ll find a large rat’s ne...

SKU: DF-SEN0159 | Brand: DFRobot

The Gravity CO2 Gas Sensor uses an MG-811 electrochemical sensing element to detect carbon dioxide concentration in the air. The output voltage decreases as CO2 concentration increases, and an onboard potentiometer le...

SKU: SF-COM-00299 | Brand: SparkFun

The Texas Instruments CD74HC4067 is a 16-channel analogue multiplexer/demultiplexer IC. It allows you to route one of 16 analogue signals to a single common pin (or vice versa) using just 4 digital control lines plus ...

SKU: SF-SEN-13715 | Brand: SparkFun

This is a stainless steel, Type-K Thermocouple probe. A thermocouple works by taking two wires made of dissimilar metals, connecting them at the two ends, and making a temperature gradient between one end and the othe...

SKU: SF-DEV-13712 | Brand: SparkFun

The SparkFun OpenLog is an open-source serial data logger based on the ATmega328 running at 16 MHz. It logs incoming serial data directly to a microSD card, supporting cards from 64 MB to 64 GB in FAT16 or FAT32 forma...

SKU: DF-DFR0029-W | Brand: DFRobot

Press to release pleasure! Our redesigned digital push buttons come with LED, immersion gold surface, and bright colored hats. A captital D at left corner indicates that it is a digital sensor. An illustration of b...

SKU: AF-166 | Brand: Adafruit

The Interlink 402 is a round force-sensitive resistor (FSR) with a 12.7 mm (0.5″) sensing area. It changes resistance based on applied pressure — the harder you press, the lower the resistance — making it a simple, lo...

SKU: DF-SEN0169 | Brand: DFRobot

This is a professional Arduino pH Sensor Meter Kit with industrial electrode. It has built-in simple, convenient , practical connection and long life (up to 1 year), which makes it very suitable for long term onli...

SKU: DF-SEN0170 | Brand: DFRobot

A three-cup anemometer kit with 0–5V analog voltage output for building custom weather stations and wind monitoring systems. The aluminium alloy construction provides high strength, weather resistance, and corrosion r...