Sensors & Input

SKU: SF-GPS-15136 | Brand: SparkFun

With GPS you are able to know where you are, where you’re going, and how to get there anywhere on Earth within 30 seconds. This means the higher the accuracy the better! GPS Real Time Kinematics (RTK) has mastered dia...

SKU: AF-1362 | Brand: Adafruit

This breakout board is the simplest way to create a project with mutiple capacitive touch sensors. No microcontroller is required here - just power with 1.8 to 5.5VDC and connect up to 5 conductive pads to the 5 left-...

SKU: AF-3721 | Brand: Adafruit

The AM2320 is a low-cost digital temperature and humidity sensor with an I2C interface — a simpler alternative to the classic DHT11/DHT22 sensors that require timing-critical bit-bang protocols. With standard I2C comm...

SKU: SF-SEN-14349 | Brand: SparkFun

This is not your normal Passive Infrared (PIR) sensor! The SparkFun AK9753 Human Presence Sensor Breakout is a Qwiic-enabled, 4-channel Nondispersive Infrared (NDIR) sensor. Each channel has a different field of view...

SKU: SS-101990004 | Brand: Seeed Studio

This  is a non-contact distance measurement module, which is also compatible with electronic brick. It’s designed for easy modular project usage with industrial performance. Features Detecting range: 3cm-4...

SKU: SF-SEN-10313 | Brand: SparkFun

The RPI-1031 is a 4-directional tilt sensor that detects orientation using internal infrared emitters and detectors. Unlike simple single-axis tilt switches, this sensor can distinguish between multiple orientations, ...

SKU: SF-BOB-11040 | Brand: SparkFun

The SparkFun LED RingCoder Breakout provides a visual position indicator for rotary encoders. Two 8-bit shift registers drive a circular LED bargraph that displays the virtual position of the encoder as it turns, givi...

SKU: AF-1727 | Brand: Adafruit

The MAX31850K breakout board is a 1-Wire thermocouple amplifier with cold-junction compensation for K-type thermocouples. Unlike SPI-based amplifiers, the 1-Wire interface allows any number of thermocouple breakouts t...

SKU: AF-1733 | Brand: Adafruit

A rugged anemometer designed for outdoor wind speed measurement with a simple analog voltage output. Connect it to any microcontroller's analog input for easy wind speed readings — no complex protocols or libraries re...

SKU: DF-SEN0006 | Brand: DFRobot

The latest model SRF05 Detection range of 3 cm from the original SRF04 -3 m, increased to 1 cm -4 meters. RF04 is compatible with the original. Also has smaller side lobes. Ultrasonic module can be used to identi...

SKU: DF-SEN0005 | Brand: DFRobot

This low cost SFR02 ultrasonic ranger has both I2C and Serial interfaces. New AutoTune algorithms intelligently back the minimum range right up to the transducer ringdown for the very best performance possible, aut...

SKU: DF-SEN0008 | Brand: DFRobot

This small sonar ranger from Devantech offers an amazing wide range from 3cm to 6m. The SRF10 is interfaced using the IIC bus. SPECIFICATIONS Voltage-5v Current-15mA Typ. 3mA Standby Frequenc...

SKU: DF-SEN0233 | Brand: DFRobot

A multifunction air quality monitor that measures particulate matter (PM2.5), formaldehyde concentration, temperature, and humidity. It uses laser scattering to detect suspended particles in the air, an electrochemica...

SKU: SF-BOB-09322 | Brand: SparkFun

A simple breakout PCB for the GP1A57HR photo interrupter (also known as a photogate, photodiode, or phototransistor). This PCB has three connections for PWR, GND, and Signal.When the gate is clear, SIG will be high (>...

SKU: AF-466 | Brand: Adafruit

The VCNL4010 sensor is a nice way to add a small-distance proximity sensor to your microcontroller project. For longer distances (in the range of cm, you can use a SHARP IR distance sensor, but those are only good ...

SKU: SF-BOB-12052 | Brand: SparkFun

Odometers are extremely useful for cars, they tell you how far you have gone, wouldn’t it be nice if you were able to have a device that does the same for electrical current? The LTC4150 SparkFun Coulomb Counter Break...

SKU: SF-COM-08348 | Brand: SparkFun

The TEMT6000x01 is a compact ambient light sensor that operates as an NPN phototransistor. The more light that hits the sensor, the stronger the base bias, producing an analog output proportional to the ambient light ...

SKU: SF-SEN-12040 | Brand: SparkFun

The INA169 is a “high-side current monitor,” which means that you place a resistor (a “shunt resistor”) on the positive power rail and the INA169 measures the voltage drop across that resistor. The INA169 outputs a sm...

SKU: SF-SEN-11859 | Brand: SparkFun

This is not your typical temperature sensor. The TMP006 Breakout can measure the temperature of an object without making contact with it. By using a thermopile to detect and absorb the infrared energy an object is emi...

SKU: SF-SEN-11769 | Brand: SparkFun

The Line Follower sensor is an add-on for your RedBot that gives your robot the ability to detect lines or nearby objects. The sensor works by detecting reflected light coming from its own infrared LED. By measurin...