Prototyping

This is high quality 840-Point Breadboard is our favourite breadboard in Australia. Material：ABS housing + Brass contact clips Size：66 x 174 x...

This kit contains all the components you need to start Arduino, Raspberry Pi. It has more than 200 pcs components, comes with a precision potent...

This 6.5" x 2.125" solderless breadboard has four bus lines each spanning the length of the board, and 63 rows of pins, enough for up to nine 14-pi...

This blue Mini Breadboard is a great way to prototype your small projects! With 170 tie points there’s just enough room to build and test simple ci...

This is a very simple board that takes a 6-12V input voltage and outputs a selectable 5V or 3.3V regulated voltage. All headers are 0.1" pitch for ...

This red Mini Breadboard is a great way to prototype your small projects! With 170 tie points there’s just enough room to build and test simple ...

Add lots more outputs to a microcontroller system with chainable shift registers. These chips take a serial input (SPI) of 1 byte (8 bits) and then...

The 400 Tie Point Interlocking Solderless Breadboard is a cute half size breadboard, good for small projects. It is 8.2cm x 6.2cm in size with a s...

This is a 'full-size' breadboard, 830 tie points. Good for small and medium projects. It's 2.2" x 7" (5.5 cm x 17 cm) with a standard double-strip ...

It can be tricky to work out which pin is which when the Raspberry Pi Pico is attached to solderless breadboard. Luckily, the MonkMakes Breadboard ...

This handy double-row, 34-pin 2x17 IDC Box Header is a slightly smaller version of the 2x20 pin IDC Box Header, often used for floppy disk drive in...

Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always crummy quality, with pads that fla...

These Adafruit Perma-Proto Quarter-Sized Breadboard PCBs bridge the gap between solderless breadboards and standard perf-boards by providing a thr...

These Male/Male Jumper Wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 6" (15...

This is high quality 840-Point Breadboard is our favourite breadboard in Australia. Material：ABS housing + Brass contact clips Size：66 x 174 x...

Perfect for bread-boarding, free wiring, etc. This box contains 6 spools of solid-core wire. The wire is easy to solder to and when bent it keep...

Rainbow coloured jumper strips, perfect for use with our mini breadboards! Each strip of jerky contains 40 individual jumper leads, 185mm long,...

These are 6" long jumper wires with male connectors on both ends. Use these to jumper from any female header on any board, to any other female h...

Looking for a chunkier Alligator clip.  These 45mm clips work well with the Micro:bit and give you a larger clip to work with.Alligator clips (o...

40 pin 15CM Jumper wire M/F Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 150mm long and...

These are 6" long jumper wires terminated as male to female. Use these to jumper from any male or female header on any board. Multiple jumpers c...

Just as small as a fingernail, this 10*2.7mm mini vibration motor features a strong vibration, low noise, easy to embed, and long lifespan. Powe...

Strangely enough, that's the technical term for this desoldering vacuum tool. Useful in cleaning up mistakes, every electrical engineer has one of ...

Used along with the solder sucker to clean up soldering messes. Wick really comes in handy when soldering or desoldering surface-mount parts. Even ...

This is your basic tube of leaded solder with a 63/37 water soluble resin core. 0.031" gauge and 15 grams (around 5ft). Easy to solder with - recom...

This is your basic tube of unleaded (Pb-free) solder with a 60/40 no clean, water soluble resin core. 0.031" gauge and 15 grams. Mix: 96.5% tin ...

Every piece of consumer electronics uses tin solder to some degree. While tin is easy to recycle the majority used in electronics still come fro...

This is a solderer’s best helper, the third hand. Comes with a heavy base, two alligator clips, a soldering iron holder, and a good magnifying g...

This is the FeatherWing Quad 2x2 - a prototyping add-on and more for all Feather boards. This is similar to our FeatherWing Proto except there are ...

Wanna improve the connection strength between your project's 3D-printed parts, and also have nice clean surfaces? Instead of gluing bits together, ...

This cable is easy to understand - you get a 3.5mm mono audio plug on one end, and two alligator clips on the other. It's also really easy to use, ...

We decided to stock this food-safe heat shrink specifically for people who were building beer-brewing or sous-vide projects using our waterproof...

Ideal for surface mount work and rework, solder paste provides a quick and easy soldering solution. Supplied in a syringe for easy application, sim...

This is your basic spool of lead free solder with a water soluble resin core. 0.031" gauge and 100 grams. This is a good spool for more advanced...

This is a standard 12mm square momentary button. What we really like is the large button head and good tactile feel (it ‘clicks’ really well). This...

This is your basic spool of leaded solder with a 63/37 water soluble resin core. 0.031" gauge and 100 grams. This is a good spool for more advanced...