Breakouts

This is a Piranha LED light module. A digital pin (LOW on, HIGH off) is used to control it. The brightness of LED can be controller via PWM output...

This is the breakout board for the thumb joystick. Pins are broken out to a 0.1" header and includes 4 mounting holes in the corners.

This is a SMD 6 pin right angle male header. We use this header on our LilyPad Main Board. Pins have 0.1" spacing between rows and between pins. ...

Huge 10mm through-hole LEDs. Features: 515-520nm Green 3.0-3.4VDC Forward Voltage 80mA Forward Current 30 degree viewing angle 16,000-22,000 MCD...

A Feather board without ambition is a Feather board without FeatherWings! This is the 8-Channel PWM or Servo FeatherWing, you can add 8 x 12-bit...

This simple board breaks out a micro-B USB connector’s VCC, GND, ID, D- and D+ pins to a 0.1" pitch header. If you want to add the popular micro-B ...

This small size breakout is programmable full-color RGB LED for hobbyists, industrial designers, prototypers, and experimenters. It is design...

DFRobot proudly presents the I/O expansion shield for Texas Instruments MSP430 LaunchPad. With the I/O expansion shield, your LaunchPad will be ...

This is not your typical temperature sensor. The TMP006 Breakout can measure the temperature of an object without making contact with it. By using ...

The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire Wheatstone bridge configuration. If ...

8, 16, 20, and 28-Pin SSOP to DIP break out boards. The footprint was rotated to accommodate different width SSOP devices and can be used with a...

This is a more universal GPS breakout board that uses a vertical SMD connector which is perfect for the GP-735T GPS receiver that we sell. It featu...

The CY7C65213 USB to UART serial breakout is designed to provide users with a means to access all available I/O pins on the IC, and to provide a...

This is a clever little breakout board for both the RGB and R/G illuminated rotary encoders. On one side, it breaks out all of the RGB pins to stan...

In this world nothing can be said to be certain, except we need headers, headers, and more headers! Each pack contains five 36-pin short fem...

This board is a simple carrier of Allegro’s ±5A ACS714 Hall effect-based linear current sensor, which offers a low-resistance (~1.2 mΩ) current pat...

The Si7021 is a low-cost, easy-to-use, highly accurate, digital humidity and temperature sensor. This sensor is ideal for environmental sensing ...

  INTRODUCTION This is a generic Arduino gas sensor. It has MQ2 probe which is able to detect LPG, i-butane, propane, methane ,alcohol, Hydroge...

One segment? No way dude! 7-Segments for life! A Feather board without ambition is a Feather board without FeatherWings! This is the Adafruit 4-...

The LSM303DLH is a triple axis accelerometer combined with a triple axis magnetic sensor. This breakout board uses the LSM303DLH to give you ...

The GP-735 is a slim, ultra-high performance, easy to use GPS smart antenna receiver. With -162dBm tracking sensitivity and only 29 second cold sta...

You will chirp with delight when you see how easy it is to make your very own 8x16 LED matrix display for any Feather. At 0.8" square, the littl...

Give your Feather a sense of place, with an Ultimate GPS FeatherWing. In 2013 we designed the Ultimate GPS module to satisfy all your GPS desires ...

The SparkFun Photon Micro OLED Shield breaks out a small monochrome, blue-on-black OLED to use with your Photon module. It’s “micro”, but it still ...