Breakouts

This is a simple breakout for the Roving Networks Bluetooth module. All pertinent pins are broken out and labeled. This new version’s headers...

This new version now has all 5 pins broken out on the connector. We have no idea what USB device you are hooking up to, but if you need to add a...

The Bluetooth Mate is very similar to our BlueSMiRF modem, but it is designed specifically to be used with our Arduino Pros and LilyPad Arduinos...

This breakout board uses the LTC3588 Piezoelectric Energy Harvester from Linear Technologies. This board can be used not only for harvesting piezoe...

Ring, Ring! Who's that callin'? It's your breadboard! Introducing Adafruit FONA MiniGSM, an adorable all-in-one cellular phone module that lets ...

Ring, Ring! Who's that callin'? It's your breadboard! Introducing Adafruit FONA MiniGSM, an adorable all-in-one cellular phone module that lets ...

Interested in learning how Bluetooth Low Energy works down to the packet level? Debugging your own BLE hardware, and trying to spot where someth...

The NXP Precision 9DoF breakout combines two of the best motion sensors we've tested here at Adafruit: The FXOS8700 3-Axis accelerometer and mag...

Yaaar! Become your very own pirate radio station with this FM radio transmitter. This breakout board, based on the best-of-class Si4713, is an all-...

This tiny breakout board features the ADMP401 MEMS microphone. One of the key advantages to this breakout and microphone is the bottom ported input...

This TFT was discontinued! We have another 2.2" TFT in the shop, so check that out if you need a 2.2" display for your project. Please note i...

The Joystick Shield sits on top of your Arduino and turns it into a simple controller. Five momentary push buttons (4+ joystick select button...

This is a simple 5V Op Amp breakout board, set up as a 2-stage amplifier with a gain of 100 (gain of 10 for each stage). The on-board trim pot sets...

The Raspberry Pi B+ has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use ...

The Raspberry Pi A+/B+/Pi 2/Pi 3/Zero has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And ...

Add motion, direction and orientation sensing to your Arduino project with this all-in-one 9-DOF sensor. Inside the chip are three sensors, one is ...

Unlike most of the other temperature sensors we have, this breakout has a really cool IR sensor from TI that can measure the temperature of an o...

Connect your own PCB to a Raspberry Pi B+ with this extra-tall female header. The female header part has extra spaces to make it 16.5mm tall: wh...

Now mounted on a breakout board, the MPL115A1 is a digital barometer that uses MEMs technology to give accurate pressure measurements between 50kPa...

Never hunt around for another crystal again, with the Si5351A clock generator breakout from Adafruit! This chip has a precision 25MHz crystal refer...

Overview DRV8838 Single Brushed DC Motor Driver Carrier, bottom view with dimensions. TI SN754410 (16-pin DIP) next to the #2135 DRV8835 c...

This is a breakout board for Honeywell’s HIH-4030 humidity sensor. The HIH-4030 measures relative humidity (%RH) and delivers it as an analog outpu...

This is a breakout board for the L298N full-bridge dual motor driver; which comes in a staggered, Multiwatt package. All pins of the L298N are...

This is a breakout board for the RN-131g WiFly GSX module, an ultra-low power 802.11b/g transceiver. This board breaks out all pins of the RN-13...