Arduino Cables and Connectors

If you're going to be adding and removing wires to a project, these 2.54 pitch headers are an ideal way to make it easy and reliable. This box h...

A simple 2-pin connector soldered onto a breadboard-friendly breakout. This is compatible with the "JST PH 2-pin" connector. Mates perfectly ...

This 4-wire cable is a little over 100mm / 4" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-P...

These jumper wires come with a twist! Instead of going from 0.1"/2.54mm pitch headers to breadboard or something like that, these are 2.54mm to ...

This is a jumper adapter cable that comes pre-terminated with a female Qwiic JST connector on one end and a breadboard hookup pigtail on the oth...

When 0.1" is too big, and JST PH's too chunky, these ultra-slim 1.25mm connectors are a reliable alternative. These are only 1.25mm pitch, but have...

A 15cm extension cable for a microSD card. Insert your microSD card into one end and then connect the other end to your Pi / PC / anything with ...

This is a handy cable for connecting a six pin GHR-06V type locking connector to breadboard friendly male pins. The six male pins that terminate on...

This is a Type-B USB cable, which is compatible with Arduino Uno. It's a 3m cable and long enough for normal use.

If you have any LEGO Mindstorm or EV3 sensors/motors/controllers you probably noticed the phone-cable-like connectors that are used to go from acce...

The cable was specially designed for LattePanda Alpha & Delta 7inch eDP display. With high flexibility and ultra-thin design, it perfectly tran...

This panel mount USB-B (female) to micro-B (male) cable enables you to more easily enclose a project that contains a USB micro-B port. The cable is...

High quality, power friendly and discrete USB A to Micro-B cables Available in a range of lengths for all possible uses (also available in red) ...

Two pin JST connector to a 2.1x 5.5mm barrel jack, 6.25 inch long jumper cable. We use this cable to adapt from a wall power supply to a relativ...

This here is your standard A-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Arduino, USBtinyISP (among other things).3 feet /...

This is a 3-pin, through-hole PH series JST connector. The pins are spaced by 2mm. We really like the solid locking feeling and high current r...

Wires play an essential role in project building. Normally, users tell lines apart by colors or onboard pin silkscreen, but mistakes sometimes happ...

We now have a handy extension cord for JST-XH projects! One end has a JST-XH socket, and the other has a matching plug. Between the two, 500mm of c...

Often used for floppy drives, 34 pin IDC cables have a 2x17 array of pins. This cable will let you connect one port to another with a festive rainb...

The Gravity 4Pin I2C/UART sensor cable is a standard Gravity series 4-Pin cable with 50cm length. One side is PH2.0-4p connector and the other side...

This high-quality 50cm analog sensor cable is equipped with a 3-pin PH2.0 plug connector on one side and a 3-pin DuPont connector on the other side...

This high-quality 50cm digital sensor cable is equipped with a 3-pin PH2.0 plug connector on one side and a 3-pin DuPont connector on the other sid...

This cable will make it super easy to use our plug-and-play STEMMA QT boards and controllers with chips, breakouts, and other devices that are I2C ...

Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the JST...